The manufacturer’s record · Page 1 of 2
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 166, ordered newest first. Dated records on this page: Jul 17, 2014–Sep 20, 2023.
Back to 2012 Dodge CHALLENGER problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10248517
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
Source components: EQUIPMENT.
Source record 10248517 at NHTSANHTSA communication ID: 10244356
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
Source components: SUSPENSION.
Source record 10244356 at NHTSANHTSA communication ID: 10248509
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
Source components: ELECTRICAL SYSTEM.
Source record 10248509 at NHTSANHTSA communication ID: 10244348
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
Source components: ELECTRICAL SYSTEM:WIRING.
Source record 10244348 at NHTSANHTSA communication ID: 10242717
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10242717 at NHTSANHTSA communication ID: 10241118
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fuel Pump Connector Replacement The technician may experience a crank/no start after the fuel pump module was replaced. This bulletin involves replacing the fuel pump connector harness (pigtail) when replacing the fuel pump module.
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, GASOLINE.
Source record 10241118 at NHTSANHTSA communication ID: 10236933
NHTSA source summary · Original PDF not reviewed by Recallfolio
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10236933 at NHTSANHTSA communication ID: 10247906
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
Source components: ENGINE AND ENGINE COOLING.
Source record 10247906 at NHTSANHTSA communication ID: 10234379
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
Source components: ENGINE AND ENGINE COOLING.
Source record 10234379 at NHTSANHTSA communication ID: 10247905
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
Source components: BACK OVER PREVENTION.
Source record 10247905 at NHTSANHTSA communication ID: 10234378
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
Source components: ENGINE AND ENGINE COOLING.
Source record 10234378 at NHTSANHTSA communication ID: 10229572
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE.
Source record 10229572 at NHTSANHTSA communication ID: 10225424
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE.
Source record 10225424 at NHTSANHTSA communication ID: 10225287
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE · STRUCTURE:INTERIOR PANELS:DOOR · UNKNOWN OR OTHER.
Source record 10225287 at NHTSANHTSA communication ID: 10221377
NHTSA source summary · Original PDF not reviewed by Recallfolio
Overhead Console If the sunglasses holder door in the overhead console will not stay closed, inspect the Latch for damage. The Latch is now released for service under part number 68599540A$.
Source components: EQUIPMENT.
Source record 10221377 at NHTSANHTSA communication ID: 10221441
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Start Condition After A Fuel Pump Replacement, Multiple Fuel System Level Related DTC?s Setting
Source components: FUEL SYSTEM, GASOLINE.
Source record 10221441 at NHTSANHTSA communication ID: 10228020
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · UNKNOWN OR OTHER.
Source record 10228020 at NHTSANHTSA communication ID: 10227983
NHTSA source summary · Original PDF not reviewed by Recallfolio
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10227983 at NHTSANHTSA communication ID: 10212248
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:FILTER/SCREEN.
Source record 10212248 at NHTSANHTSA communication ID: 10220687
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR · UNKNOWN OR OTHER.
Source record 10220687 at NHTSANHTSA communication ID: 10212290
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
Source record 10212290 at NHTSANHTSA communication ID: 10230180
NHTSA source summary · Original PDF not reviewed by Recallfolio
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
Source components: ENGINE AND ENGINE COOLING.
Source record 10230180 at NHTSANHTSA communication ID: 10221594
NHTSA source summary · Original PDF not reviewed by Recallfolio
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
Source components: ENGINE AND ENGINE COOLING.
Source record 10221594 at NHTSANHTSA communication ID: 10221154
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
Source components: ELECTRICAL SYSTEM.
Source record 10221154 at NHTSANHTSA communication ID: 10194007
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
Source components: POWER TRAIN.
Source record 10194007 at NHTSANHTSA communication ID: 10221150
NHTSA source summary · Original PDF not reviewed by Recallfolio
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
Source components: POWER TRAIN.
Source record 10221150 at NHTSANHTSA communication ID: 10221097
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
Source components: POWER TRAIN.
Source record 10221097 at NHTSANHTSA communication ID: 10220843
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
Source components: POWER TRAIN.
Source record 10220843 at NHTSANHTSA communication ID: 10190590
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
Source components: POWER TRAIN.
Source record 10190590 at NHTSANHTSA communication ID: 10190589
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
Source components: ENGINE AND ENGINE COOLING.
Source record 10190589 at NHTSANHTSA communication ID: 10215879
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
Source record 10215879 at NHTSANHTSA communication ID: 10187058
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE AND ENGINE COOLING.
Source record 10187058 at NHTSANHTSA communication ID: 10221813
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle
Source components: ELECTRICAL SYSTEM:IGNITION · UNKNOWN OR OTHER.
Source record 10221813 at NHTSANHTSA communication ID: 10180203
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10180203 at NHTSANHTSA communication ID: 10175743
NHTSA source summary · Original PDF not reviewed by Recallfolio
Disinfectant Solution Recommended for COVID-19
Source components: EQUIPMENT · STRUCTURE.
Source record 10175743 at NHTSANHTSA communication ID: 10175735
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10175735 at NHTSANHTSA communication ID: 10175733
NHTSA source summary · Original PDF not reviewed by Recallfolio
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
Source components: FUEL SYSTEM, GASOLINE.
Source record 10175733 at NHTSANHTSA communication ID: 10175501
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speed Control Operates Intermittently
Source components: VEHICLE SPEED CONTROL.
Source record 10175501 at NHTSANHTSA communication ID: 10175088
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speed Control Operates Intermittently
Source components: VEHICLE SPEED CONTROL.
Source record 10175088 at NHTSANHTSA communication ID: 10174168
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speed Control Operates Intermittently
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT:ELECTRICAL.
Source record 10174168 at NHTSANHTSA communication ID: 10170314
NHTSA source summary · Original PDF not reviewed by Recallfolio
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
Source components: SUSPENSION.
Source record 10170314 at NHTSANHTSA communication ID: 10220101
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
Source components: STRUCTURE.
Source record 10220101 at NHTSANHTSA communication ID: 10220099
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
Source components: STRUCTURE.
Source record 10220099 at NHTSANHTSA communication ID: 10220098
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
Source components: VISIBILITY.
Source record 10220098 at NHTSANHTSA communication ID: 10220097
NHTSA source summary · Original PDF not reviewed by Recallfolio
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
Source components: EQUIPMENT · STRUCTURE.
Source record 10220097 at NHTSANHTSA communication ID: 10169249
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
Source components: EQUIPMENT · STRUCTURE.
Source record 10169249 at NHTSANHTSA communication ID: 10169247
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
Source components: EQUIPMENT.
Source record 10169247 at NHTSANHTSA communication ID: 10169246
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
Source components: VISIBILITY.
Source record 10169246 at NHTSANHTSA communication ID: 10169245
NHTSA source summary · Original PDF not reviewed by Recallfolio
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
Source components: STRUCTURE.
Source record 10169245 at NHTSANHTSA communication ID: 10166537
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10166537 at NHTSANHTSA communication ID: 10162466
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter Adapter If replacing Oil Filter Adapter due to oil leak, please be aware a seal kit is available for repair. If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.
Source components: ENGINE · EQUIPMENT.
Source record 10162466 at NHTSANHTSA communication ID: 10217484
NHTSA source summary · Original PDF not reviewed by Recallfolio
Servicing Lower Control Arm Inner Pivot Bushings This bulletin discusses replacement of the lower control arm inner pivot bushings.
Source components: SUSPENSION · SUSPENSION:FRONT:CONTROL ARM:LOWER ARM.
Source record 10217484 at NHTSANHTSA communication ID: 10216303
NHTSA source summary · Original PDF not reviewed by Recallfolio
Servicing Lower Control Arm Inner Pivot Bushings This bulletin discusses replacement of the lower control arm inner pivot bushings.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · SUSPENSION.
Source record 10216303 at NHTSANHTSA communication ID: 10219830
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
Source components: VISIBILITY:WINDSHIELD WIPER/WASHER.
Source record 10219830 at NHTSANHTSA communication ID: 10217521
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
Source components: FUEL SYSTEM, GASOLINE.
Source record 10217521 at NHTSANHTSA communication ID: 10139989
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
Source components: ENGINE AND ENGINE COOLING.
Source record 10139989 at NHTSANHTSA communication ID: 10139978
NHTSA source summary · Original PDF not reviewed by Recallfolio
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
Source components: SEAT BELTS.
Source record 10139978 at NHTSANHTSA communication ID: 10139985
NHTSA source summary · Original PDF not reviewed by Recallfolio
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
Source components: SEAT BELTS.
Source record 10139985 at NHTSANHTSA communication ID: 10223855
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
Source components: VISIBILITY/WIPER.
Source record 10223855 at NHTSANHTSA communication ID: 10228120
NHTSA source summary · Original PDF not reviewed by Recallfolio
Manual Transmission Shifter Noise This bulletin involves greasing or replacing the manual transmission rear shifter bushing. Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.
Source components: BACK OVER PREVENTION · EQUIPMENT · POWER TRAIN.
Source record 10228120 at NHTSANHTSA communication ID: 10181486
NHTSA source summary · Original PDF not reviewed by Recallfolio
Manual Transmission Shifter Noise This bulletin involves greasing or replacing the manual transmission rear shifter bushing. Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.
Source components: EQUIPMENT · POWER TRAIN.
Source record 10181486 at NHTSANHTSA communication ID: 10141286
NHTSA source summary · Original PDF not reviewed by Recallfolio
Manual Transmission Shifter Noise This bulletin involves greasing or replacing the manual transmission rear shifter bushing. Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
Source record 10141286 at NHTSANHTSA communication ID: 10218303
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10218303 at NHTSANHTSA communication ID: 10140254
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10140254 at NHTSANHTSA communication ID: 10139956
NHTSA source summary · Original PDF not reviewed by Recallfolio
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
Source components: VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10139956 at NHTSANHTSA communication ID: 10218037
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hands Free Module Prompts Begin Erroneously.
Source components: ELECTRICAL SYSTEM.
Source record 10218037 at NHTSANHTSA communication ID: 10215071
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hands Free Module Prompts Begin Erroneously.
Source components: ELECTRICAL SYSTEM.
Source record 10215071 at NHTSANHTSA communication ID: 10138948
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hands Free Module Prompts Begin Erroneously This bulletin involves diagnosing and based on outcome, either performing a USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: · Reduced ?Device Reading? wait time after connecting a device to the remote USB port. · Call / dial separation improves upon names being recognized as phone numbers. · Improved sound quality during Bluetooth streaming. · Increased iPod and iPhone compatibility. · SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). · Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. · Previous button will return the song currently being played to the beginning of the track. · AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10138948 at NHTSANHTSA communication ID: 10121927
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
Source components: ENGINE AND ENGINE COOLING.
Source record 10121927 at NHTSANHTSA communication ID: 10218133
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: PCM Software Enhancements.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10218133 at NHTSANHTSA communication ID: 10159945
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: PCM Software Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the Powertrain Control Module (PCM): ? U0140 - Lost Communication With Body Control Module. ? U0401 - Implausible Data Received From ECM/PCM. ? P0441 - Evap Purge System Performance. ? P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. This software update also has improvements for fuel pump relay cycling during remote starts.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10159945 at NHTSANHTSA communication ID: 10074946
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10074946 at NHTSANHTSA communication ID: 10218142
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin involves selectively erasing and reprogramming the Powertrain Control
Source components: ELECTRICAL SYSTEM.
Source record 10218142 at NHTSANHTSA communication ID: 10215176
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin involves selectively erasing and reprogramming the Powertrain Control
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10215176 at NHTSANHTSA communication ID: 10159927
NHTSA source summary · Original PDF not reviewed by Recallfolio
Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may describe hearing the fuel pump relay cycling during remote start or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM: ? U0140 - Lost Communication With Body Control Module (BCM). ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. ? P0522 - Engine Oil Pressure Sensor Circuit Low. ? P0108 - Manifold Absolute Pressure Sensor Circuit High. ? P1239 - Engine Oil Temperature Too Low. ? P0298 - Engine Oil Temperature Too High.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
Source record 10159927 at NHTSANHTSA communication ID: 10074955
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10074955 at NHTSANHTSA communication ID: 10148691
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: PCM Software Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs) have been set: ? U0401-00 - Implausible Data Received From ECM/PCM ? P0441 - Evap Purge System Performance ? P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1 This software update also has improvements for fuel pump relay cycling during remote starts.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE · FUEL SYSTEM, GASOLINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10148691 at NHTSANHTSA communication ID: 10058837
NHTSA source summary · Original PDF not reviewed by Recallfolio
2011-2012 DODGE CHALLENGER; 2012 DODGE CHARGER; 2012 CHRYSLER 300: MALFUNCTION INDICATOR LAMP ILLUMINATION. BULLETIN ON SELECTIVELY ERASING AND REPROGRAMMING POWERTRAIN CONTROL MODULE *CN
Source components: EQUIPMENT.
Source record 10058837 at NHTSANHTSA communication ID: 10149662
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 3.6L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience one or more of the following: ? Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) U0140 - Lost Communication With Body Control Module (TIPM) stored in the Engine Control Module (ECM) memory. ? For 2011 vehicles built prior to February 2, 2011, the customer may experience a condition known as ?Idle Buffeting? while the vehicle is idling. This condition can be similar to driving down the road with one rear window down and all others rolled up, causing a thumping or buffeting sound. The idle speed will be adjusted to 650 RPM to correct this condition.
Source components: POWER TRAIN.
Source record 10149662 at NHTSANHTSA communication ID: 10058031
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHRYSLER 2011-2013 DODGE CHALLENGER : THIS BULLETIN INVOLVES REPROGRAMMING THE POWER CONTROL MODULE WITH THE NEWEST SOFTWARE. *LJ
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10058031 at NHTSANHTSA communication ID: 10150546
NHTSA source summary · Original PDF not reviewed by Recallfolio
RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. SYMPTOM/CONDITION FOR RHB RADIOS ONLY: ? Trip planner does not save a route after is was created. ? Route guidance does not activate after the vehicle shuts down. ? Longitude entry does not allow enough digits. ? CD/DVD will not play. ? Navigation accept screen will not clear. ? Navigation shows ?acquiring signal? for an extended period of time. ? New navigation graphics.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · POWER TRAIN.
Source record 10150546 at NHTSANHTSA communication ID: 10144868
NHTSA source summary · Original PDF not reviewed by Recallfolio
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
Source components: ENGINE.
Source record 10144868 at NHTSANHTSA communication ID: 10223599
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
Source components: ENGINE AND ENGINE COOLING.
Source record 10223599 at NHTSANHTSA communication ID: 10148573
NHTSA source summary · Original PDF not reviewed by Recallfolio
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
Source components: ENGINE.
Source record 10148573 at NHTSANHTSA communication ID: 10221067
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
Source components: EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE.
Source record 10221067 at NHTSANHTSA communication ID: 10139897
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
Source components: ENGINE AND ENGINE COOLING.
Source record 10139897 at NHTSANHTSA communication ID: 10229936
NHTSA source summary · Original PDF not reviewed by Recallfolio
RBZ Or RHB Radio Software Enhancements
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10229936 at NHTSANHTSA communication ID: 10139800
NHTSA source summary · Original PDF not reviewed by Recallfolio
RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics.
Source components: EQUIPMENT.
Source record 10139800 at NHTSANHTSA communication ID: 10229966
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL Illumination For P0730 And Transmission Shift Enhancements
Source components: POWER TRAIN.
Source record 10229966 at NHTSANHTSA communication ID: 10139799
NHTSA source summary · Original PDF not reviewed by Recallfolio
FLASH: MIL Illumination For P0730 And Transmission Shift Enhancements This bulletin involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find that Diagnostic Trouble Code (DTC) P0730 Incorrect Gear Ratio is setting erroneously. In addition to correcting the DTC, the following Transmission Control Module (TCM) calibration improvements are now available. These updates are broken down by vehicle line and engine category.WK, WD, JK and LC Vehicles equipped with a 3.6L engine (Sales Code ERB) Hanging in gear during HOT ambient temperature conditions while vehicle is loaded or towing. Delayed downshift during acceleration at speeds above 48 kph. (Taiwan, Japan, and China market only). Delayed downshift when driving at altitudes higher than 2500 feet. Inconsistent shifting when towing or while driving up or down steep hills. Delayed upshift while driving in 4 low Intermittent delayed shift. Delayed engagement when shifting from drive to reverse while in 4 low. (JK Rubicon only) Delayed shift from second gear while towing or driving on steep grades. (JK Rubicon only) Intermittent delayed engagement from reverse to drive. Less than desired shift quality in AutoStick mode. (LC vehicles only) Fuel economy improvements. (LC vehicles only)LC Vehicles equipped with a 5.7L engine (Sales Codes EZH or EZC) Hanging in gear during HOT ambient temperature conditions while vehicle is loaded or towing. Bump sensation felt during deceleration or braking. Fuel economy improvements.LC and WK Vehicles equipped with a 6.4L engine (Sales Codes ESH or ESG) Bump sensation felt during deceleration or braking. (LC only) Inconsistent downshift during Wide Open Throttle (WOT) accelerations at highway speeds (i.e. passing). Transmission enhancements to improve acceleration while in reverse going uphill on steep
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE · POWER TRAIN.
Source record 10139799 at NHTSANHTSA communication ID: 10063729
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10063729 at NHTSANHTSA communication ID: 10229945
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension)
Source components: ENGINE AND ENGINE COOLING.
Source record 10229945 at NHTSANHTSA communication ID: 10139771
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
Source record 10139771 at NHTSANHTSA communication ID: 10229935
NHTSA source summary · Original PDF not reviewed by Recallfolio
RBZ Or RHB Radio Software Enhancements
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10229935 at NHTSANHTSA communication ID: 10139767
NHTSA source summary · Original PDF not reviewed by Recallfolio
RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only).
Source components: EQUIPMENT.
Source record 10139767 at NHTSANHTSA communication ID: 10220993
NHTSA source summary · Original PDF not reviewed by Recallfolio
RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10220993 at NHTSANHTSA communication ID: 10139594
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality (examples may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the following:~ 1. Power on radio~2. Press MENU H/K~3. Press System Setup S/K~4. Press Manage HDD S/K~5. Press Display Available Space on HDD S/K~6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes~ Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. ~ Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EQUIPMENT · FUEL SYSTEM, GASOLINE · POWER TRAIN · SUSPENSION · VISIBILITY.
Source record 10139594 at NHTSANHTSA communication ID: 10217710
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Audio From The Radio Caused By The Amplifier Muting Audio This bulletin involves replacing the Amplifier if required. The customer may indicate that there is no audio sound and/or radio is muted. This may happen when the audio is at a higher volume. The audio system will mute and remains ?muted? until the key is cycled. The audio system may defaults to surround sound after a key cycle. On further inspection one or more of the following DTCs may be found: B1460-92 Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92 Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92 Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92 Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92 Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92 Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92 Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92 Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92 Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92 Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92 Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92 Channel 12 Audio Speaker Output-Performance or Incorrect Operation.
Source components: EQUIPMENT · EQUIPMENT:APPLIANCE:TV/RADIO/SPEAKERS · EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10217710 at NHTSANHTSA communication ID: 10141225
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Audio From The Radio Caused By The Amplifier Muting Audio This bulletin involves replacing the Amplifier if required. The customer may indicate that there is no audio sound and/or radio is muted. This may happen when the audio is at a higher volume. The audio system will mute and remains ?muted? until the key is cycled. The audio system may defaults to surround sound after a key cycle. On further inspection one or more of the following DTCs may be found: B1460-92 Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92 Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92 Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92 Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92 Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92 Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92 Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92 Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92 Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92 Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92 Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92 Channel 12 Audio Speaker Output-Performance or Incorrect Operation.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10141225 at NHTSANHTSA communication ID: 10062685
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ELECTRICAL SYSTEM.
Source record 10062685 at NHTSA