2001 Chevrolet TRACKER Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 306, ordered newest first. Dated records on this page: Oct 10, 2000–Jun 16, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 16, 2014Service Bulletin/Repair Instructions
PIC5588B
NHTSA communication ID: 10125953
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a customer?s request to install OnStar Bluetooth. Dealer should be advised at this time, there are no provisions to add this option to vehicles that were not built with it.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: INFORMATION PROVIDED BY BULLETIN FOR ALL 2012 AND PRIOR GENERAL MOTOR TRUCKS AND PASSENGER VEHICLES REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING 1988-2004 CHEVROLET AND GMC LIGHT DUTY TRUCKS. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING 1988-2004 CHEVROLET AND GMC LIGHT DUTY TRUCKS. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS SERVICE VOICEMAIL MESSAGE IS TO INFORM THAT AN AIR CONDITIONER FUSE COULD HAVE FAILED DURING THE COLD WEATHER MONTHS DUE TO INCORRECT SIGNAL AND ICE LOADING. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMMENT THAT THE RIGHT END OR LEFT FRONT WINDOWS TIP FORWARD WHEN BEING RAISED AND HAVE A TENDENCY TO BIND IN THE WINDOW CHANNEL. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME OWNERS MAY COMMENT ON A SQUEAK OR RATTLE TYPE NOISE THAT IS COMING FROM THE INSTRUMENT PANEL, USUALLY IN THE AREA OF THE GAUGE CLUSTER, RADIO OR LEFT OUTBOARD AIR OUTLET. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS BULLETIN IS BEING ISSUED TO INFORM DEALERS OF THE CORRECT PART NUMBER TO USE WHEN REPLACING SPARE TIRE COVERS FOR CERTAIN VEHICLES EQUIPPED WITH COVERS THAT ARE TOO TIGHT. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMMENT THAT THE HVAC SYSTEM IS NOT WORKING CORRECTLY. WHEN THE CONTROL IS MOVED TO THE DOWN OR FLOOR (HEAT) POSITION, AIR CONTINUES TO FLOW FROM THE END VENTS OF THE DASH. NLM
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING THE 1996 THROUGH 2000 TOYOTA CAVALIER. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME PDI TECHNICIANS OR CUSTOMERS MAY COMMENT THAT THE SPARE TIRE COVER IS TOO TIGHT AND THAT A SEAM OR A ZIPPER MAY BLOWOUT OR THE ZIPPER TANG MAY EVEN BREAK OFF. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN ENGINE TICK NOISE SIMILAR TO THAT EXPERIENCED WITH THE L34 2.0 LITER FOUR-CYLINDER ENGINE WHEN AIR IS INGESTED INTO HYDRAULIC VALVE LIFTERS. *TT
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMMENT THAT THERE IS A CREAKING TYPE SOUND COMING FROM THE RIGHT REAR WHEEL OPENING OR THE DOG LEG AREA WHEN DRIVING SLOWLY OR IN PARKING LOT TYPE MANEUVERS ON 4-DOOR MODELS ONLY. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
EXPERIENCING A TICK TYPE NOISE COMING FROM THE ENGINE WHILE THE ENGINE IS RUNNING DURING COLD OR HOT OPERATION. THE CONDITION WILL BE MOST NOTICEABLE ON VEHICLES THAT HAVE BEEN STORED FOR EXTENDED PERIODS OF TIME WITHOUT RUNNING THE ENGINE OR ON VEHICLES FOLLOWING A REPAIR TO THE VALVE LIFTERS AND CAMSHAFTS. *TT
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE.