The manufacturer’s record · Page 3 of 6
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 509, ordered newest first. Dated records on this page: Oct 30, 2012–Dec 11, 2014.
Back to 2001 Chevrolet TAHOE problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10126237
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
Source components: VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
Source record 10126237 at NHTSANHTSA communication ID: 10114776
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Fender wheel-opening heights are related to, but distinct from, trim height. The front wheel-opening height is known as P height, and the rear wheel-opening height is known as R height. Adjust and heights that are out of specification. After all adjustments are done, perform a front-end alignment and check headlight aim.
Source components: EXTERIOR LIGHTING:HEADLIGHTS · STRUCTURE:FRAME AND MEMBERS · SUSPENSION.
Source record 10114776 at NHTSANHTSA communication ID: 10114746
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
Source components: ENGINE.
Source record 10114746 at NHTSANHTSA communication ID: 10114705
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10114705 at NHTSANHTSA communication ID: 10245951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10245951 at NHTSANHTSA communication ID: 10135356
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10135356 at NHTSANHTSA communication ID: 10114325
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10114325 at NHTSANHTSA communication ID: 10114313
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10114313 at NHTSANHTSA communication ID: 10135342
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
Source record 10135342 at NHTSANHTSA communication ID: 10135337
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10135337 at NHTSANHTSA communication ID: 10135322
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
Source record 10135322 at NHTSANHTSA communication ID: 10150639
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · SERVICE BRAKES, HYDRAULIC.
Source record 10150639 at NHTSANHTSA communication ID: 10142229
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10142229 at NHTSANHTSA communication ID: 10137808
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10137808 at NHTSANHTSA communication ID: 10112251
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112251 at NHTSANHTSA communication ID: 10150627
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the dealers on how to submit a product information report.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10150627 at NHTSANHTSA communication ID: 10142208
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the dealers on how to submit a product information report.
Source components: EQUIPMENT.
Source record 10142208 at NHTSANHTSA communication ID: 10137787
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the dealers on how to submit a product information report.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137787 at NHTSANHTSA communication ID: 10246647
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pre-Formed and Pre-Flared Hydraulic Brake Pipe Kits Now Available for Service
Source components: SERVICE BRAKES.
Source record 10246647 at NHTSANHTSA communication ID: 10054261
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC/CADILLAC: ANYTIME HYDRAULIC BRAKE PIPES ASSEMBLY NEED REPLACING, PRE-FORMED AND PRE-FLARED BRAKE PIPES ARE AVAILABLE, EXCEPT REAR AXLE CROSSOVER PIPE. MODEL 1999-2007 SILVERADO, SIERRA, 2000-2006 ESCALADE MODELS, AVALANCHE, SUBURBAN, TAHOE, YUKON MODELS. *PE UPDATED 7/18/14. *PE UPDATED 12/9/14. *PE
Source components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER.
Source record 10054261 at NHTSANHTSA communication ID: 10112160
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10112160 at NHTSANHTSA communication ID: 10112137
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10112137 at NHTSANHTSA communication ID: 10140437
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
Source components: ENGINE · EQUIPMENT.
Source record 10140437 at NHTSANHTSA communication ID: 10138592
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138592 at NHTSANHTSA communication ID: 10137842
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10137842 at NHTSANHTSA communication ID: 10112116
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112116 at NHTSANHTSA communication ID: 10140367
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
Source components: EQUIPMENT.
Source record 10140367 at NHTSANHTSA communication ID: 10138582
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138582 at NHTSANHTSA communication ID: 10137832
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
Source components: EQUIPMENT.
Source record 10137832 at NHTSANHTSA communication ID: 10140363
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the dealers on how to submit a product information report.
Source components: EQUIPMENT.
Source record 10140363 at NHTSANHTSA communication ID: 10138578
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the dealers on how to submit a product information report.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138578 at NHTSANHTSA communication ID: 10137828
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the dealers on how to submit a product information report.
Source components: EQUIPMENT.
Source record 10137828 at NHTSANHTSA communication ID: 10248444
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vehicle Recalls
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10248444 at NHTSANHTSA communication ID: 10125953
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10125953 at NHTSANHTSA communication ID: 10246952
NHTSA source summary · Original PDF not reviewed by Recallfolio
Programming And Activation Of Replacement OnStar Modules.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10246952 at NHTSANHTSA communication ID: 10137901
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10137901 at NHTSANHTSA communication ID: 10246624
NHTSA source summary · Original PDF not reviewed by Recallfolio
Car and Truck Fix it Right the First Time Issues
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10246624 at NHTSANHTSA communication ID: 10135219
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
Source components: EXTERIOR LIGHTING.
Source record 10135219 at NHTSANHTSA communication ID: 10135218
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
Source components: EQUIPMENT.
Source record 10135218 at NHTSANHTSA communication ID: 10111810
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111810 at NHTSANHTSA communication ID: 10135198
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
Source components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS.
Source record 10135198 at NHTSANHTSA communication ID: 10111850
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10111850 at NHTSANHTSA communication ID: 10111846
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a customer?s request to install OnStar Bluetooth. Dealer should be advised at this time, there are no provisions to add this option to vehicles that were not built with it.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111846 at NHTSANHTSA communication ID: 10247681
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information On Requests To Add OnStar Bluetooth Option.
Source components: EQUIPMENT.
Source record 10247681 at NHTSANHTSA communication ID: 10245950
NHTSA source summary · Original PDF not reviewed by Recallfolio
Canadian Customers Unable To Place Calls In The United States
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10245950 at NHTSANHTSA communication ID: 10111964
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111964 at NHTSANHTSA communication ID: 10111927
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FUEL SYSTEM, GASOLINE · SERVICE BRAKES, HYDRAULIC.
Source record 10111927 at NHTSANHTSA communication ID: 10111894
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111894 at NHTSANHTSA communication ID: 10190932
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190932 at NHTSANHTSA communication ID: 10190931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190931 at NHTSANHTSA communication ID: 10112013
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10112013 at NHTSANHTSA communication ID: 10112001
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Suspension System message on the Driver Information Center and the rear suspension ride height is incorrect. Technician will find Diagnostic Trouble Code C0696 or C0711 set in Electronic Suspension Control. Technician will need to inspect air compressor assembly for wire damage and repair any damage do not replace the complete air compressor assembly. Some vehicles may have a Service Suspension System message on the Driver Information Center and may also comment that the rear suspension ride height may be low under a heavy payload. Technician will follow published Service Information diagnostics and if determine if the sensor needs to be replaced technician will need to replace a complete air filter, dryer, and sensor assembly. Some vehicles may have a loose hose hanging down in the left rear of the vehicle. Technician will replace the auto leveling compressor air inlet filter and hose assembly. Also some vehicles may have automatic level control compressor is no longer performing a self-test at start up. Be advised the automatic level system normally will not or very infrequently cycle the compressor at key up.
Source components: SERVICE BRAKES, AIR:SUPPLY:COMPRESSOR · SUSPENSION.
Source record 10112001 at NHTSANHTSA communication ID: 10111997
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
Source components: EQUIPMENT.
Source record 10111997 at NHTSANHTSA communication ID: 10111977
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed.
Source components: ENGINE.
Source record 10111977 at NHTSANHTSA communication ID: 10190934
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190934 at NHTSANHTSA communication ID: 10190933
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190933 at NHTSANHTSA communication ID: 10133103
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides directions on submitting different PIRs
Source components: BACK OVER PREVENTION: SENSING SYSTEM: RADAR.
Source record 10133103 at NHTSANHTSA communication ID: 10133086
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
Source components: FUEL SYSTEM, DIESEL · FUEL SYSTEM, GASOLINE · FUEL SYSTEM, OTHER.
Source record 10133086 at NHTSANHTSA communication ID: 10118885
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on brake line kits now available and how to service them on vehicle.
Source components: SERVICE BRAKES.
Source record 10118885 at NHTSANHTSA communication ID: 10246645
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pre-Formed and Pre-Flared Hydraulic Brake Pipe Kits Now Available for Service
Source components: SERVICE BRAKES.
Source record 10246645 at NHTSANHTSA communication ID: 10112331
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112331 at NHTSANHTSA communication ID: 10112382
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the percentage of UV protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces UV rays down to 4% or less. Front side door glass reduces UV rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
Source components: VISIBILITY:WINDSHIELD.
Source record 10112382 at NHTSANHTSA communication ID: 10113227
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
Source components: EQUIPMENT.
Source record 10113227 at NHTSANHTSA communication ID: 10246631
NHTSA source summary · Original PDF not reviewed by Recallfolio
Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
Source record 10246631 at NHTSANHTSA communication ID: 10113177
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10113177 at NHTSANHTSA communication ID: 10052488
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: IF THE SERVICE SUSPENSION SYSTEM IS DISPLAYED ON THE DIC, THE TRIM HEIGHT MAY BE INCORRECT, LOOSE COMPRESSOR INLET HOSE, OR THE COMPRESSOR SELF TEST MAY BE INOPERATIVE. ALSO INCLUDED SUBURBAN LD MY 2001-2013, YUKON DENALI XL MY 2013, YUKON XL LD 2001-2013 *JS
Source components: SUSPENSION.
Source record 10052488 at NHTSANHTSA communication ID: 10113019
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Suspension System message on the Driver Information Center and the rear suspension ride height is incorrect. Technician will find Diagnostic Trouble Code C0696 or C0711 set in Electronic Suspension Control. Technician will need to inspect air compressor assembly for wire damage and repair any damage do not replace the complete air compressor assembly. Some vehicles may have a Service Suspension System message on the Driver Information Center and may also comment that the rear suspension ride height may be low under a heavy payload. Technician will follow published Service Information diagnostics and if determine if the sensor needs to be replaced technician will need to replace a complete air filter, dryer, and sensor assembly. Some vehicles may have a loose hose hanging down in the left rear of the vehicle. Technician will replace the auto leveling compressor air inlet filter and hose assembly. Also some vehicles may have automatic level control compressor is no longer performing a self-test at start up. Be advised the automatic level system normally will not or very infrequently cycle the compressor at key up.
Source components: ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · SUSPENSION.
Source record 10113019 at NHTSANHTSA communication ID: 10247693
NHTSA source summary · Original PDF not reviewed by Recallfolio
Suspension.
Source components: SUSPENSION.
Source record 10247693 at NHTSANHTSA communication ID: 10245332
NHTSA source summary · Original PDF not reviewed by Recallfolio
Suspension.
Source components: SUSPENSION.
Source record 10245332 at NHTSANHTSA communication ID: 10038344
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. ALL 2014 AND PRIOR GM PASSENGER CARS AND TRUCKS. *KB
Source components: LATCHES/LOCKS/LINKAGES:DOORS:LATCH.
Source record 10038344 at NHTSANHTSA communication ID: 10139066
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10139066 at NHTSANHTSA communication ID: 10139019
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information on High Oil Pressure on Startup After Engine Replacement Concern.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10139019 at NHTSANHTSA communication ID: 10113074
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT.
Source record 10113074 at NHTSANHTSA communication ID: 10130652
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides Warranty Administration - New Labor Codes information.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130652 at NHTSANHTSA communication ID: 10130627
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130627 at NHTSANHTSA communication ID: 10130626
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 01-08-49-017A to add new pricing information and payment terms.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130626 at NHTSANHTSA communication ID: 10134640
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
Source components: WHEELS.
Source record 10134640 at NHTSANHTSA communication ID: 10112885
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
Source components: EQUIPMENT.
Source record 10112885 at NHTSANHTSA communication ID: 10112857
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
Source components: ELECTRICAL SYSTEM.
Source record 10112857 at NHTSANHTSA communication ID: 10133130
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
Source components: STRUCTURE:BODY.
Source record 10133130 at NHTSANHTSA communication ID: 10112702
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: ENGINE.
Source record 10112702 at NHTSANHTSA communication ID: 10112697
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN.
Source record 10112697 at NHTSANHTSA communication ID: 10112681
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a planetary gear whine noise in first and second gear. Technician should compare the noise to a like vehicle. Technician will need to check the build date of the transmission, if it was built after 09/01/2003 and it is determined that a vehicle has an abnormal amount of noise, perform the rear unit end play check. Technician will replace the output planetary gear set if end play is out of specification. The transmission assembly will need to be replaced if the end play is with in specification.
Source components: POWER TRAIN.
Source record 10112681 at NHTSANHTSA communication ID: 10112664
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
Source components: ELECTRICAL SYSTEM.
Source record 10112664 at NHTSANHTSA communication ID: 10112655
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
Source components: TIRES · WHEELS.
Source record 10112655 at NHTSANHTSA communication ID: 10112641
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112641 at NHTSANHTSA communication ID: 10126171
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT.
Source record 10126171 at NHTSANHTSA communication ID: 10112607
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10112607 at NHTSANHTSA communication ID: 10138213
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
Source components: EQUIPMENT · WHEELS.
Source record 10138213 at NHTSANHTSA communication ID: 10137471
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
Source components: WHEELS.
Source record 10137471 at NHTSANHTSA communication ID: 10112600
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
Source components: POWER TRAIN:AXLE ASSEMBLY.
Source record 10112600 at NHTSANHTSA communication ID: 10138211
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
Source components: EQUIPMENT.
Source record 10138211 at NHTSANHTSA communication ID: 10137469
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
Source components: EQUIPMENT.
Source record 10137469 at NHTSANHTSA communication ID: 10138201
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
Source components: EQUIPMENT.
Source record 10138201 at NHTSANHTSA communication ID: 10137459
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10137459 at NHTSANHTSA communication ID: 10137458
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for requesting a new key code for customers with lost or stolen keys
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10137458 at NHTSANHTSA communication ID: 10126200
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10126200 at NHTSANHTSA communication ID: 10112546
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES · SERVICE BRAKES, HYDRAULIC.
Source record 10112546 at NHTSANHTSA communication ID: 10112528
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
Source components: ELECTRICAL SYSTEM.
Source record 10112528 at NHTSANHTSA communication ID: 10112523
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have slip in forward ranges immediately after replacing the input housing. Technician will inspect the 3-4 clutches and the forward clutch oil feed passages for leakage between circuits. Technician should apply regulated compressed air to the 3-4 clutch feed hole and the forward clutch feed hole one at a time with the input housing. Technician will need to replace the input housing if there is an air leak 3-4 clutches.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:CLUTCH ASSEMBLY.
Source record 10112523 at NHTSA