Recalls
NHTSA communication ID: 10248444
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vehicle Recalls
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10248444 at NHTSAThe manufacturer’s record · Page 12 of 16
2011 Chevrolet SUBURBAN
Manufacturer communications & TSBs.Page 12
Original record summaries, dates and identifiers for this model-year. Records 1,101–1,200 of 1,580, ordered newest first. Dated records on this page: Jan 21, 2014–Jun 30, 2014.
Back to 2011 Chevrolet SUBURBAN problems & recallsRead the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
PIT5180A
NHTSA communication ID: 10125984
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a whistle noise coming from the driver?s side "A" pillar area when driving around 50 mph with the Heater-Vent-Air Conditioning in recirculation mode. Technician will need to reseal the Vehicle Identification Number plate rivets using room temperature vulcanization silicone sealer from the underside.
Source components: EQUIPMENT · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
Source record 10125984 at NHTSA050308002F
NHTSA communication ID: 10126308
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal.
Source components: SUSPENSION.
Source record 10126308 at NHTSAPIP4112P
NHTSA communication ID: 10125972
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: ENGINE · POWER TRAIN.
Source record 10125972 at NHTSAPI1266
NHTSA communication ID: 10126301
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the techline/service programming systems.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10126301 at NHTSAPI0373B
NHTSA communication ID: 10126291
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.
Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES.
Source record 10126291 at NHTSAPIC5088E
NHTSA communication ID: 10126285
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10126285 at NHTSAPIC5088E
NHTSA communication ID: 10125956
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Technician will need to use a scan tool and verify current Digital Radio Receiver Status under Data Display. Technician will need to look at the second line labeled Digital Radio Receiver Status will display a number of 00 - 04. Technician will repair per the status code.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10125956 at NHTSAPIC5588B
NHTSA communication ID: 10125953
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10125953 at NHTSA05-00-89-029C
NHTSA communication ID: 10126280
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a information to the dealer for the requirements need for equipment.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10126280 at NHTSAPIP4401E
NHTSA communication ID: 10125947
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have the check engine light, tow/haul, Supplemental Inflatable Restraint, cruise control or other various indicators or warning lamps will not come on in the instrument panel. Tech will need to the Tech 2 scan tool to command the instrument panel indicator lights on. If the light do not turn on technician should inspect (AUX HVAC) 10 amp fuse in the under-hood fuse block for open or high resistance.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10125947 at NHTSAPIT5209A
NHTSA communication ID: 10125946
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Technician will need to use a scan tool to verify that the alarm was activated by the inclination sensor. If the trigger is the inclination sensor, inspect the sensor's mounting location. Technician will need to relocate the sensor if it is attached to the driver's side lower Heater-Vent-Air Conditioning duct. Technician will need to reinstall the sensor to the top of the Body Control Module bracket.
Source components: BACK OVER PREVENTION · BACK OVER PREVENTION: BACK-UP ALARM · ELECTRICAL SYSTEM · STRUCTURE.
Source record 10125946 at NHTSA12-00-89-002B
NHTSA communication ID: 10126278
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
Source components: EQUIPMENT.
Source record 10126278 at NHTSA03-00-89-006K
NHTSA communication ID: 10126275
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides dealers with more information on how to better prep a vehicle for pre-delivery.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10126275 at NHTSAPIP4653E
NHTSA communication ID: 10125933
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10125933 at NHTSAPIT5209A
NHTSA communication ID: 10247767
NHTSA source summary · Original PDF not reviewed by Recallfolio
Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10247767 at NHTSAPIT5180A
NHTSA communication ID: 10247738
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whistle Noise From Drivers Side A Pillar Area.
Source components: STRUCTURE.
Source record 10247738 at NHTSAPIT5209A
NHTSA communication ID: 10247112
NHTSA source summary · Original PDF not reviewed by Recallfolio
Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10247112 at NHTSAPIT5180A
NHTSA communication ID: 10247083
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whistle Noise From Drivers Side A Pillar Area.
Source components: STRUCTURE.
Source record 10247083 at NHTSA09-03-10-013B
NHTSA communication ID: 10137937
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty.
Source components: TIRES.
Source record 10137937 at NHTSA12-07-30-001D
NHTSA communication ID: 10137935
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
Source components: ENGINE · POWER TRAIN.
Source record 10137935 at NHTSA02-07-30-029W
NHTSA communication ID: 10137934
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10137934 at NHTSA03-06-03-004L
NHTSA communication ID: 10137932
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10137932 at NHTSAPIC5687D
NHTSA communication ID: 10112082
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that loose connection between the vehicle and a Bluetooth phone. Technician will need to use a scan tool to check the "Firmware Over-the-Air" value. If the "Firmware Over-the-Air" value is up to date and customer's concern is still present contact General Motors Technical Assistance Center for further assistance.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10112082 at NHTSA03-03-10-007I
NHTSA communication ID: 10137928
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.
Source components: EQUIPMENT · TIRES.
Source record 10137928 at NHTSA00-03-10-006J
NHTSA communication ID: 10137927
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer.
Source components: EQUIPMENT · TIRES.
Source record 10137927 at NHTSAPIP4833E
NHTSA communication ID: 10112079
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Auxiliary Transmission Fluid Pump Control Module and Auxiliary Transmission Fluid Pump placed on parts restriction by General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10112079 at NHTSAPIT4821D
NHTSA communication ID: 10112078
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 2-Mode Drive Motor Generator Battery placed on parts restriction by General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ENGINE AND ENGINE COOLING.
Source record 10112078 at NHTSA13-00-89-004I
NHTSA communication ID: 10137919
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
Source components: EQUIPMENT.
Source record 10137919 at NHTSA12-08-132-001B
NHTSA communication ID: 10137918
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains if the fuse is open when the customer plugs in the trailer, that it may be the cause if diagnostics finds no problems to that point.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10137918 at NHTSA06-06-05-001F
NHTSA communication ID: 10137915
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains a normal condition from changes in Exhaust Tone for Active Fuel Management Engines when in Three or Four Cylinder Mode
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE.
Source record 10137915 at NHTSA06-00-89-029J
NHTSA communication ID: 10137914
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides tips on how to care for the interior of the vehicle using products.
Source components: EQUIPMENT.
Source record 10137914 at NHTSAPIP3119M
NHTSA communication ID: 10112069
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
Source record 10112069 at NHTSAPI1233
NHTSA communication ID: 10137903
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin states to add the DTC symptom byte to the documentation to help aid engineering pinpoint concerns when trying to locate a root cause.
Source components: EQUIPMENT.
Source record 10137903 at NHTSA05-06-04-035D
NHTSA communication ID: 10137901
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10137901 at NHTSA02-07-30-029V
NHTSA communication ID: 10137890
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT · POWER TRAIN.
Source record 10137890 at NHTSAPIC5687D
NHTSA communication ID: 10246983
NHTSA source summary · Original PDF not reviewed by Recallfolio
Checking Smartphone Bluetooth Software Update Status
Source components: EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE.
Source record 10246983 at NHTSA09-00-89-002I
NHTSA communication ID: 10135227
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10135227 at NHTSA01-08-42-001J
NHTSA communication ID: 10135219
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
Source components: EXTERIOR LIGHTING.
Source record 10135219 at NHTSA02-08-42-001G
NHTSA communication ID: 10135218
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
Source components: EQUIPMENT.
Source record 10135218 at NHTSAPIC5491F
NHTSA communication ID: 10111811
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10111811 at NHTSAPIT3099L
NHTSA communication ID: 10111810
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111810 at NHTSAPIP5168C
NHTSA communication ID: 10111805
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE).
Source record 10111805 at NHTSA13-00-89-004H
NHTSA communication ID: 10135201
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10135201 at NHTSAPI1216
NHTSA communication ID: 10135200
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to install a new cabin air filter kit for vehicles that did not have one if the customer whants one installed to fix the concern of dust intruding into cabin interior.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10135200 at NHTSAPIP3343E
NHTSA communication ID: 10111783
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
Source components: FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS.
Source record 10111783 at NHTSA1406130001
NHTSA communication ID: 10250013
NHTSA source summary · Original PDF not reviewed by Recallfolio
High Voltage Safety ? High Voltage Disabling
Source components: ELECTRICAL SYSTEM.
Source record 10250013 at NHTSA12050B
NHTSA communication ID: 10245824
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Axle Grinding Noise, Vibration - Inspect Rear Axle
Source components: SUSPENSION.
Source record 10245824 at NHTSAPIP-5168-C
NHTSA communication ID: 10055840
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: SOME VEHICLES/TRUCKS MAY EXPERIENCE A NO CRANKING OR STARTING, CAUSED BY POSSIBLE EXCESSIVE LEAKAGE FROM CYLINDER PAST EXHAUST OR INTAKE VALVE, LOW STATIC COMPRESSION, SENSOR IS DISCONNECTED, OR WHILE CRANKING, VALVE TRAIN FAILS TO MOVE. MODEL 2009-2014 CORVETTE, CAMARO, EXPRESS, SS, SILVERADO, SUBURBAN, TAHOE, SAVANA, SIERRA, YUKON. *PE
Source components: ENGINE.
Source record 10055840 at NHTSA03-06-03-004K
NHTSA communication ID: 10137887
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10137887 at NHTSAPIP3343D
NHTSA communication ID: 10111875
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
Source components: ENGINE.
Source record 10111875 at NHTSA13-00-89-004G
NHTSA communication ID: 10137866
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
Source components: EQUIPMENT.
Source record 10137866 at NHTSAPIT5264
NHTSA communication ID: 10111850
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10111850 at NHTSAPIC5374C
NHTSA communication ID: 10111849
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10111849 at NHTSAPIC5959A
NHTSA communication ID: 10111848
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10111848 at NHTSAPIT4864F
NHTSA communication ID: 10111846
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a customer?s request to install OnStar Bluetooth. Dealer should be advised at this time, there are no provisions to add this option to vehicles that were not built with it.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111846 at NHTSAPIC4801F
NHTSA communication ID: 10111845
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10111845 at NHTSAPIT4864F
NHTSA communication ID: 10247681
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information On Requests To Add OnStar Bluetooth Option.
Source components: EQUIPMENT.
Source record 10247681 at NHTSAPIC5687C
NHTSA communication ID: 10246982
NHTSA source summary · Original PDF not reviewed by Recallfolio
Checking Smartphone Bluetooth Software Update Status
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10246982 at NHTSAPIT5264
NHTSA communication ID: 10245950
NHTSA source summary · Original PDF not reviewed by Recallfolio
Canadian Customers Unable To Place Calls In The United States
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10245950 at NHTSAPIC5959A
NHTSA communication ID: 10073396
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10073396 at NHTSA08-08-48-003H
NHTSA communication ID: 10138655
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to install double sided tape to the windshield molding to correct the customers concern of a tapping or clicking noise at the winshield area.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · VISIBILITY:WINDSHIELD.
Source record 10138655 at NHTSAPIC5491E
NHTSA communication ID: 10111966
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111966 at NHTSAPIC3011H
NHTSA communication ID: 10111964
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111964 at NHTSA12-07-30-001C
NHTSA communication ID: 10138646
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
Source components: ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN.
Source record 10138646 at NHTSAPIP5184
NHTSA communication ID: 10111962
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that when replacing the camshaft part number 12626660. Technician will need to ensure that the date code and the finish of the camshaft. If the cam is discolored or has chatter marks, have parts department send the cam back as (MR code7) new defective.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111962 at NHTSAPIP5168B
NHTSA communication ID: 10111956
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: ENGINE.
Source record 10111956 at NHTSA10-08-64-002C
NHTSA communication ID: 10138640
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.
Source record 10138640 at NHTSA12-03-10-002A
NHTSA communication ID: 10138639
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the technician the proper way to install and torque the wheel.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · WHEELS.
Source record 10138639 at NHTSA09-03-10-016B
NHTSA communication ID: 10138638
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
Source components: WHEELS.
Source record 10138638 at NHTSA12-03-10-001A
NHTSA communication ID: 10138637
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES · WHEELS:RIM.
Source record 10138637 at NHTSA08-03-10-006E
NHTSA communication ID: 10138631
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
Source components: TIRES · WHEELS:RIM.
Source record 10138631 at NHTSA05-03-10-020E
NHTSA communication ID: 10138630
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains the use of Nitrogen in GM tires.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES.
Source record 10138630 at NHTSA07-03-10-008D
NHTSA communication ID: 10138629
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information regarding the normal tire wear condition of slight or mild tire feathering and recommended practices.
Source components: TIRES.
Source record 10138629 at NHTSA13-00-89-004F
NHTSA communication ID: 10138621
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138621 at NHTSAPIP5088A
NHTSA communication ID: 10111928
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 6.6L Duramax Diesel Engine Part number 12638502 has been placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
Source components: ENGINE · FUEL SYSTEM, DIESEL.
Source record 10111928 at NHTSAPIT4943C
NHTSA communication ID: 10111927
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FUEL SYSTEM, GASOLINE · SERVICE BRAKES, HYDRAULIC.
Source record 10111927 at NHTSA02-08-98-002E
NHTSA communication ID: 10138609
NHTSA source summary · Original PDF not reviewed by Recallfolio
The informational bulletin provides a procedure to remove and repair rust from a Hem Flange.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138609 at NHTSA05-08-48-001D
NHTSA communication ID: 10138606
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletion provides the dealer technician information and guidelines for claiming a windshield.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · VISIBILITY:WINDSHIELD.
Source record 10138606 at NHTSA99-01-39-004E
NHTSA communication ID: 10138605
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10138605 at NHTSAPI0360C
NHTSA communication ID: 10138604
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides service information to the dealer technicians that the remote start will not work with the ONSTAR REMOTE Link applcation
Source components: ELECTRICAL SYSTEM.
Source record 10138604 at NHTSAPI0488D
NHTSA communication ID: 10138601
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure to inspect the transmissions filter for splits or cracks to correct the customers concern for no forward, reverse or slips.
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10138601 at NHTSAPIC5453A
NHTSA communication ID: 10111894
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111894 at NHTSAPIP5104A
NHTSA communication ID: 10111892
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a cold engine tick noise for 50 seconds at start up. Technician determines if the tick noise is possibly coming from the exhaust manifold, as this noise could easily be mistaken for an engine tick noise. If your SI diagnosis does not isolate the cause of this concern, this concern should be considered a vehicle design characteristic of the ECM calibration and no additional repairs should be performed.
Source components: ENGINE.
Source record 10111892 at NHTSAPIP4792D
NHTSA communication ID: 10253135
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cold Extended Crank .
Source components: ENGINE AND ENGINE COOLING.
Source record 10253135 at NHTSA99-08-51-007F
NHTSA communication ID: 10190932
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190932 at NHTSA99-08-51-007F
NHTSA communication ID: 10190931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190931 at NHTSA04-00-89-053F
NHTSA communication ID: 10137784
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
Source components: EQUIPMENT.
Source record 10137784 at NHTSAPIC5959
NHTSA communication ID: 10112045
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10112045 at NHTSAPIP4792D
NHTSA communication ID: 10112043
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a an extended crank on cold start, brief rough running on cold start, black exhaust color, and/or Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0172 and or P0175. Technician will need to check the Fuel Alcohol Content parameter found in the Fuel Trim Data List of the scan tool and the measured ethanol content of a fuel sample using the J44175 tester. If the difference is 17% or greater, reprogram the Engine Control Module with the latest calibrations from TIS2web.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
Source record 10112043 at NHTSAPIT4474E
NHTSA communication ID: 10112033
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have navigation or radio screen is blank or flashes on and off, no sound from speakers, and rear DVD screen inoperative. Technician will find Diagnostic Trouble Codes B1265, B1288, or B1289. Technician will need to repair circuit 7066.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10112033 at NHTSAPIT4684B
NHTSA communication ID: 10112032
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a rear camera display being inoperative when shifting into reverse. Technician should check for a loose or disconnected X421/X322 connector behind the right side "C" pillar trim. Technician should also check for pinched, Open or shorted wires on camera circuits 7641, 7642, and 6799.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · ELECTRICAL SYSTEM:WIRING.
Source record 10112032 at NHTSAPIT5201A
NHTSA communication ID: 10112024
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code B2555 may be found in a Driver and/or Passenger Door Module. Technician should ignore the Diagnostic Trouble Code if set in a DDM and/or PDM on a vehicles not equipped with front door panel courtesy lights.
Source components: INTERIOR LIGHTING · STRUCTURE:BODY:DOOR.
Source record 10112024 at NHTSA11-00-89-002B
NHTSA communication ID: 10137781
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137781 at NHTSAPIT5208A
NHTSA communication ID: 10112023
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that after refueling the fuel gauge will show empty. Technician may find Diagnostic Trouble Code P2636 has set. Technician should be advised that the vehicle is being refueled with the engine running or ignition on.
Source components: FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY · FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM.
Source record 10112023 at NHTSAPIP5168A
NHTSA communication ID: 10112018
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published "Engine Cranks But Does Not Run" diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112018 at NHTSAPIC5953
NHTSA communication ID: 10112013
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10112013 at NHTSAPIT5215A
NHTSA communication ID: 10112010
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that after installing the GM Accessory Heated Seat Kit, one or more of the following issues may be present the heated seat back and/or bottom turns off after approximately 30 seconds and after turning on the heated seat switch, the indicators remain on, but the seat is not heating. Technician may find Diagnostic Trouble Codes B1935 Sym 0E, B2180 Sym 0E, B2425 Sym 0D, and/or B2430 Sym 0D. Technician will need to inspect the accessory heated seat wiring harness and make sure the heater element connectors are installed correctly.
Source components: SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
Source record 10112010 at NHTSAPIT5195A
NHTSA communication ID: 10112009
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10112009 at NHTSAPIP5092A
NHTSA communication ID: 10112006
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns.
Source components: PARKING BRAKE:DRIVELINE.
Source record 10112006 at NHTSA