2017 Chevrolet SILVERADO Manufacturer communications & TSBs.Page 7
Original record summaries, dates and identifiers for this model-year. Records 601–700 of 896, ordered newest first. Dated records on this page: Feb 16, 2017–Jul 7, 2017.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jul 7, 2017Service Bulletin/Repair Instructions
PIT5535B
NHTSA communication ID: 10114065
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.
Source components: LANE DEPARTURE · VISIBILITY:WINDSHIELD.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesthat some customers may comment that the rear camera display is too bright at night. General Motors Engineering is investigating the condition, and this PI will be updated when further information is available.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about an ECM calibration update to address DTC P054F setting.This PI updated from engineering aware of concern to valid calibration covered in TSB 17-NA-171.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about an ECM calibration update to address aDTC P10D1. This PI updated from engineering aware of concern to valid calibration covered in TSB 17-NA-171.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about an ECM calibration update to address ahesitation, bump, chuggle, jerk or a feeling of harshness between 25 and 45 MPH, light acceleration with the transmission in 3rdgear. This PI updated from engineering aware of concern to valid calibration covered in TSB 17-NA-171.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information and definitionsto the technician about vehicles that have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed and no debris is found in the transmission fluid pan the technicians are instructed to flush the transmission fluid three times. If debris is found in the transmission fluid pan the technicians are instructed to also replace the torque converter.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates Vehicles may be setting DTC P2101 falsely. In 2017 the K2XX introduced a “Driver Door Open Prime” (DDOP) feature that improves cold startability. The engineering investigation has determined that an intermittent pulse on the ECM RUN/CRANK input (during vehicle door unlock), initializes the Electronic Throttle Control (ETC) diagnostics that falsely sets P2101 when the DDOP occurs as the customer opens the driver door. Many of the reported P2101 failures show that the vehicle battery was in a reduced charge state (new dealer stock or extended radio operation with the engine off).Run the engine for 1 minute, soak the vehicle for 5 hours (required to re-initialize the DDOP) and verify that the P2101 does not reset.Return the vehicle to the customer
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Product Quality Center has ended the part restriction for the T87A Transmission Control Module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17235 - Service Update. On certain vehicles the electric power steering (EPS) rack gear teeth were not properly heat treated. Dealers will replace the EPS gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when watching a movie the audio does not match the video when playing though the vehicles speakers. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the radio to correct conditions of Distorted Outbound Audio During Bluetooth Phone Calls due to a software concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of DTC P2101 Throttle Actuator Position Performance Set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a fuel leak, fuel odor, and or engine stall.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on the availability of a new spring replacement tonneau latch to replace an original quarter turn latch that has broken.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides technicians with information on the normal condition of white, milky or cloudy appearance of front differential fluid.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communication advises technicians that the NOX Sensors restriction for the 2017 6.6L diesel engine Regular Production Option Code (L5P) has ended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates the frontview camera will not calibrate / learn. Update GDS 2 to the latest Diagnostic package 2017.3.1 release 04/03/17. Then go back and do the learn.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 40 and 128 KM/H (25 and 80 MPH) at a steady state.
NHTSA source summary · Original PDF not reviewed by Recallfolio
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17139 - Service Update. Certain vehicles may have delamination on the electronic control module (ECM) printed circuit board (PCB) causing open circuits. This condition may result in possible no start or stall. Dealers are to replace and reprogram the ECM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesMultiple Electrical Issues Including: Stalling / Crank No Start / Lighting Issues / Memory And Power Seats / Power Windows Inoperative / Heated Cooled Seats / Trailering / ABS MIL / Stability Message / etc. caused by certain ground bolts not havingproper hardening. A ground bolt without the proper hardening may not achieve torque causing a poor ground connection. Dealership are to inspect the ground bolt for proper torque and replace if necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to Add 1 quart of coolant to the upper chamber of the surge tank in order to bring the level up to the bottom of the fill neck to correct a condition of the coolant surge tank appears low and/or a low coolant message displayed intermittently due to the fill process at the plant cannot purge all of the air from the cooling system and surge tank.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17108 01 - Service Update (revised parts list). Certain vehicles may have a fracture in the parking lever support window which, if overloaded, may result in a further fracture of the transmission case. This may cause the park system to be inoperative. Dealers will inspect transmission case for mold number and Julian date and replace suspect transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains to the technician how to validate software calibrations have been tampered with by means of using aftermarket mods.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician when diagnosing intermittent circuit concerns to look at the connector for missing weather pack seals that could allow water intrusion into the connector and lead to corrosion on the terminals.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17108 - Service Update. Certain vehicles may have a fracture in the parking lever support window which, if overloaded, may result in a further fracture of the transmission case. This may cause the park system to be inoperative. Dealers will inspect transmission case for mold number and Julian date and replace suspect transmission.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17098 - Service Update. Certain vehicles may have a condition where a false failure action is being taken when it is not required. This condition can result in the transmission holding the last known safe gear for 6 seconds. A malfunction indicator lamp (MIL) is set when this default happens more than 2 times, and reduced propulsion can happen for all 8-speed transmission applications. Dealers will reprogram the transmission control module (TCM).
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician on the steps to diagnose the concern and the steps to repair the concern. Customer hears a rattle or ticking noise that is louder inside the vehicle than outside. A-This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17028 01 - Customer Satisfaction. Certain vehicles may not have had the Diesel Engine Owner Manual Supplement and/or insert installed at the assembly plant. Dealers will insert the Owner Manual Diesel Engine Supplement in the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17105 - Customer Satisfaction Program. Certain vehicles, equipped with a DuraMax Diesel Engine (L5P) and Dual Generators (KHB), may have been built with an accessory drive belt idler pulley intended for other applications. The pulley?s centerline and capacity differs from the design intent pulley. This difference in alignment and durability may cause the accessory drive belt at some point to come off the accessory drive system. Without an accessory drive belt, the vehicle will lose engine cooling, battery charging, power steering, power brakes, and air conditioning operation. All other systems will function normally. Delaers will replace the idler pulley the belt or both.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17048 Customer Satisfaction. Certain vehicles may have a condition in which the transfer case actuator motor brake sticks in the open position inside the transfer case actuator assembly. If 1) the actuator motor brake sticks open, 2) the vehicle is on asurface with an angle greater than zero but less than two degrees, 3) the vehicle is parked in 4LO, 4) the system is warm, and 5) the vehicle ignition is turned ?Off,? there is potential for vehicle rollback due to the range fork slipping into neutral. The brake sticking condition will set diagnostic trouble code C0326 58 and a ?Service AWD? warning will appear on the driver information center. Dealers are to replace the transfer case actuator assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin is providing a procedure to reprogram the HMI module to correct multiple conditions including Waiting for Update Media Message, Voice Command For Calling Bluetooth Phone Contacts Inoperative, Intermittent Loss of Rear Camera Gridlines, Service Rear Vision System Message, Radio Turns On Unwanted At Startup, and/or Navigation Radio Destination State Defaults To WV, Intermittent Radio/display Resets, Volume Control Inoperative.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a customer concern ofSIR light on with any DTC set in the SDM. During diagnostics a technician may find water in the SDM connector and is unable to locate a leak path. Dealer is instructed to inspect X150 connector for being broken allowing water into the body harness. Dealer to repair affected connector or harness as needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 48 and 104 KM/H (30 and 65 MPH) at a steady state.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Engineering Information - Noise Originating from Front Shock/Strut While Traveling at Low Speeds and/or Going Over Bumps.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections missing from radio Settings menu intermittently. Technicians will find the Heater-Vent-Air Conditioning does change but the lower radio display is blank. Technician will need to update the radio using Service Programming System with the latest software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on High Oil Pressure during Initial Start of Vehicle is considered a normal characteristic and no repairs should be completed for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates that a technician might find a vehicle with no power transmitted to the front axle in four wheel drive. If vehicle has regular production option NQF the technician finds that with vehicle in four wheel drive with solid indicator light but the front wheels do not assist in moving vehicle he is to verify when shifting the transfer case to four wheel drive the light is solid If that switch illuminated solid then all operations to achieve four wheel drive were completed successfully. Technician is to inspect pictured item and ensure that the body ring that the synchronizer engages has not separated from theTransfer Case Front Output Shaft Drive Sprocket. If so then replace the transfer case front output drive shaft sprocket as needed. If vehicle has regular production option NQG and the customer indicates that the transfer case was in four wheel drive with that indicator light on solid in the instrument panel cluster but the front wheels were not assisting in vehicle movement technician is to verify the following, shift the transfer case to four wheel drive and ensure that the four wheel drive in the instrument panel cluster is on solid. Technician is to inspect pictured item and ensure that the body ring that the synchronizer engages has not separated from theTransfer Case Front Output Shaft Drive Sprocket.If so then replace the transfer case front output drive shaft sprocket as needed.
Source components: POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17065 - Service Update. When certain vehicles, equipped with base body or chassis (RPO ZW9) and without rear vision camera ready (RPO 5F9) are shifted into reverse, the installed calibration is looking for a camera input that was not part of the requested truck build and ?Service Rear Camera? error message is displayed. Dealers will reprogram the radio with the correct calibration.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides Information on Using Voice Pass-Thru to Access Voice Recognition Commands on Cell Phone and how it does not work on models equipped with IOA and IOB radios.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.