2018 Chevrolet CORVETTE Manufacturer communications & TSBs.Page 10
Original record summaries, dates and identifiers for this model-year. Records 901–1,000 of 1,007, ordered newest first. Dated records on this page: Mar 29, 2017–Dec 18, 2017.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Dec 18, 2017Service Bulletin/Repair Instructions
PIP4578B
NHTSA communication ID: 10126975
NHTSA source summary · Original PDF not reviewed by Recallfolio
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 40 and 128 KM/H (25 and 80 MPH) at a steady state.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure to install a power steering gear cooling duct for track use to decrease temperature with the steering gear.
Source components: STEERING:HYDRAULIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ECU are not the cause.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
Source components: ENGINE · EQUIPMENT · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the 8L45 and 8L90 park actuator rod. The dealer technician is advised to call the GM Product Quality Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option.
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the T87A Transmission Control Module. The dealer technician is advised to call the GM Product Quality Center for further assistance.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear View Camera Guidelines Not Present at Times Condition Some customers may report that the Rear View Camera (RVC) guidelines are temporarily not available at times but the RVC will remain on during the concern. Additionally, no related DTCs will be found if this bulletin applies. One example of when this concern may be observed is if a customer quickly starts the car and immediately places the shifter in Reverse while the infotainment system is still in the initial boot up process. Cause This is a result of the RVC image being provided via an alternate robust RVC feed from the Video Bypass Module (NGI systems) or from the radio (BYOM2 and Info 3.0 systems). This alternate robust RVC feed is provided in the event that the primary RVC feed is not available for any reason just to ensure that the RVC image is always present when in reverse. Correction If this concern is experienced and no related codes are present, DO NOT replace any parts as it is normal for the RVC guidelines not to be present when the RVC image being displayed is from the alternate robust RVC feed. If this occurs after quickly starting the vehicle and immediately placing the shifter in Drive, the RVC guidelines can be displayed again in most cases if they are really needed by safely coming to a stop, placing the transmission in Park for a moment, and then shifting to Reverse again.
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All or Some Options May Be Missing from Driver Information Center (DIC) Info Pages Menu Due to Them Not Being Selected Condition Some customers may comment that with the Info option selected from the main menu (1), the Info Pages are blank (2) when scrolling up and down. If information is present when scrolling up and down, they may also comment that certain items are missing when compared to other like vehicles Cause This condition may be caused when all/some of the options not being selected in the active info pages menu. Correction If this concern is encountered, determine if all/any of the selections in the active info pages menu are not selected. To do this, follow the steps listed below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Clicking Noise from Front Wheels While Turning at Slow Speeds Condition Some customers may comment on a clicking noise emanating from the front wheels location. This condition may be more predominant at low speeds (10-20 mph or 16-32 km/h) during full wheel lock turns on dry clean pavement. Cause - his may be caused by interaction between the wheel mounting face and the wheel mounting surfaces on the brake rotor. Correction - lean both of the wheels mounting surfaces
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rattle Type Noise/Sound from the Drive Support Assembly (DSA) Condition Some customers may comment on a rattle type noise. Further investigation will reveal the noise is originating from the drive support assembly area. Cause This may be due to the propeller shaft hub clamp bolt coming loose. Correction Replace the propeller shaft hub clamp bolt.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:SHAFT:INPUT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for programming the low speed LAN module due to the mirrors memory position reverse tilt position is inoperative.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on replacing the prop shaft hub clamp (AT) or the input shaft frt bearing (MT) whenever the driveline support assembly has been removed for repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Technician should not replace the Human Machine Interface for this concern, power cycling of the Human Machine Interface fuse should restore communication. Technician should be advised that the Human Machine Interface and Global Diagnostic System 2 interaction concern has been reported to engineering for root cause and correction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The PI was created to advise of an engineering investigation for a concern of unable to connect toOnStar Virtual Advisor when selecting "New Destination" in the OnStar menu.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:MECHANICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Technician should not replace the Human Machine Interface for this concern, power cycling of the Human Machine Interface fuse should restore communication. Technician should be advised that the Human Machine Interface and Global Diagnostic System 2 interaction concern has been reported to engineering for root cause and correction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will replace it via the website provided.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that do not recognize the SD card when it is used in the Performance Data Recorder (PDR) system.The SD card needs to be formatted to FAT32 and also have a class 10 designation in order to be compatible with the system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up.