2009 Chevrolet COLORADO Manufacturer communications & TSBs.Page 4
Original record summaries, dates and identifiers for this model-year. Records 301–400 of 1,042, ordered newest first. Dated records on this page: Feb 20, 2017–Oct 10, 2018.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 10, 2018Service Bulletin/Repair Instructions
PIT5099D
NHTSA communication ID: 10147367
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic transmission into park while the transfer case is in 4 wheel drive low (4LO) range. Dealers technician's are advised this condition should be deemed a normal characteristic of 4WD low operation.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an engine that misfires, possibly coming to a stop or on acceleration. This may be caused by contaminated fuel. Technician will need to inspect the inside of the fuel rail and fuel tank for signs of fuel contamination. If fuel contamination is present, refer to the "Fuel System Cleaning" procedure in Service Information and clean the inside of the fuel tank, fuel lines and fuel rail. Also the fuel injectors will need to be cleaned by following "Fuel Injector Cleaning Procedure" in Service Information. Technician may report a repeat misfire concerns on these cylinders caused by sticking valves after cleaning the fuel system. If the valves are sticking do not replace the cylinder head or valves until first attempting to clean them. This should be done by using the cleaning procedures listed in the latest version of PIP5029.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
Source components: COMMUNICATION · FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact.
Source components: SUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY · SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
Source components: ENGINE · EQUIPMENT · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to lube the rear leaf springs on vehicles with the condition of a squeak noise originating from the rear of the vehicle.
Source components: SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - Service Stabilitrak Message - Service Steering Message due to dirt and debris.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.