2009 Chevrolet AVALANCHE Manufacturer communications & TSBs.Page 11
Original record summaries, dates and identifiers for this model-year. Records 1,001–1,100 of 1,297, ordered newest first. Dated records on this page: Feb 20, 2013–Aug 5, 2013.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Aug 5, 2013Service Bulletin/Repair Instructions
PIP4138N
NHTSA communication ID: 10113177
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
11273A - Special Coverage (additional population added). The throttle position sensor may cause the engine to run rough and cause the malfunction indicator lamp and/or and Engine Reduced Power message to illuminate. If this occurs, it could result in reduced engine power. If the condition occurs within the stated terms, dealers will replace the throttle position sensor and reprogram the engine control module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about an owner that may request to have a different style mirror installed on their vehicle or request a different mirror before they purchase the vehicle. Swapping mirrors on vehicles equipped with Side Blind Zone Alert, Regular Production Option Code UFT, is not recommended. On other vehicles tech will need to verify if the vehicle is equipped with door modules or not. On vehicles with door modules technician will need to contact Techline Customer Support for new calibrations for both doors. On vehicles not equipped with door modules no calibrations are needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: IF THE SERVICE SUSPENSION SYSTEM IS DISPLAYED ON THE DIC, THE TRIM HEIGHT MAY BE INCORRECT, LOOSE COMPRESSOR INLET HOSE, OR THE COMPRESSOR SELF TEST MAY BE INOPERATIVE. ALSO INCLUDED SUBURBAN LD MY 2001-2013, YUKON DENALI XL MY 2013, YUKON XL LD 2001-2013 *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a malfunction indicator light or service anti-lock brake system message displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code C0055 or P2771. Technician will need to check for excess movement of the tone wheel or output shaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section.
Source components: STEERING · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Suspension System message on the Driver Information Center and the rear suspension ride height is incorrect. Technician will find Diagnostic Trouble Code C0696 or C0711 set in Electronic Suspension Control. Technician will need to inspect air compressor assembly for wire damage and repair any damage do not replace the complete air compressor assembly. Some vehicles may have a Service Suspension System message on the Driver Information Center and may also comment that the rear suspension ride height may be low under a heavy payload. Technician will follow published Service Information diagnostics and if determine if the sensor needs to be replaced technician will need to replace a complete air filter, dryer, and sensor assembly. Some vehicles may have a loose hose hanging down in the left rear of the vehicle. Technician will replace the auto leveling compressor air inlet filter and hose assembly. Also some vehicles may have automatic level control compressor is no longer performing a self-test at start up. Be advised the automatic level system normally will not or very infrequently cycle the compressor at key up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. ALL 2014 AND PRIOR GM PASSENGER CARS AND TRUCKS. *KB
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information onUnexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry® Phone - Bluetooth® Issues Concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that after installing the GM Accessory Heated Seat Kit, one or more of the following issues may be present the heated seat back and/or bottom turns off after approximately 30 seconds and after turning on the heated seat switch, the indicators remain on, but the seat is not heating. Technician may find Diagnostic Trouble Codes B1935 Sym 0E, B2180 Sym 0E, B2425 Sym 0D, and/or B2430 Sym 0D. Technician will need to inspect the accessory heated seat wiring harness and make sure the heater element connectors are installed correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information.
Source components: EQUIPMENT · TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: LOW ENGINE OIL PRESSURE, NO OIL PRESSURE, AND/OR ENGINE NOISE. THIS COULD BE THE RESULT OF A STICKING OIL PUMP PRESSURE RELIEF VALVE. *KB
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during that time. Technician should be advised that Traffic and Weather data from local reporting stations and then send the updated info process may take up to 24 minutes. Technician should test for full operation of the XM band if the system has not started receiving the Traffic and weather update within 30 minutes. Also ensure the customer has not shut XM NavTraffic off in the user settings of the navigation radio. Technician will need to contact XM customer assistance to review the account status and verify that the XM Traffic option has been enabled and is available in the area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Technician will need to use a scan tool to verify that the alarm was activated by the inclination sensor. If the trigger is the inclination sensor, inspect the sensor's mounting location. Technician will need to relocate the sensor if it is attached to the driver's side lower Heater-Vent-Air Conditioning duct. Technician will need to reinstall the sensor to the top of the Body Control Module bracket.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 12-04-21-001A to add the 2013 model year, clarify the information from the previous bulletin and to add data throughout. The document should be reviewed and treated as new information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a radio display that will show "LOCKED" or "THEFT LOCK". Technician will need to replace the radio If the radio stills displays "LOCKED" or "THEFT LOCK" after SPS programming.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have navigation or radio screen is blank or flashes on and off, no sound from speakers, and rear DVD screen inoperative. Technician will find Diagnostic Trouble Codes B1265, B1288, or B1289. Technician will need to repair circuit 7066.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure to adjust the transmission dipstick tube and/or install the transmission fluid filler tube sleeve to eliminate a tick, buzz or rattle noise from the front of dash, transmission filler tuber cracked or broken.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code B2555 may be found in a Driver and/or Passenger Door Module. Technician should ignore the Diagnostic Trouble Code if set in a driver door module and/or Passenger Door Module on a vehicles not equipped with front door panel courtesy lights.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:DOOR · VEHICLE SPEED CONTROL.