Original record summaries, dates and identifiers for this model-year. Records 601–700 of 713, ordered newest first. Dated records on this page: Sep 1, 2005–May 6, 2013.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 6, 2013Service Bulletin/Repair Instructions
07-00-89-037F
NHTSA communication ID: 10139025
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during that time. Technician should be advised that Traffic and Weather data from local reporting stations and then send the updated info process may take up to 24 minutes. Technician should test for full operation of the XM band if the system has not started receiving the Traffic and weather update within 30 minutes. Also ensure the customer has not shut XM NavTraffic off in the user settings of the navigation radio. Technician will need to contact XM customer assistance to review the account status and verify that the XM Traffic option has been enabled and is available in the area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · FUEL SYSTEM, GASOLINE · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure on how to correctly check and adjust fuses within the instrument panel fuse block for concerns with components fused through the instrument panel fuse block
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure on how to correctly check and adjust fuses within the instrument panel fuse block for concerns with components fused through the instrument panel fuse block
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: J-35616-64B TERMINAL TEST PROBE AND REPLACEMENT TERMINAL. ALSO INCLUDED MODELS VERANO, REGAL, LACROSSE, CTS, SRX, VOLT, SONIC, MALIBU, IMPALA, EQUINOX, CRUZE, AVALANCHE, TAHOE SUBURBAN, SILVERADO, SIERRA, YUKON, AND TERRAIN FOR MODEL YEAR 2013. MODEL ESCALADE MODEL YEAR 2012-2013. MODEL PONTIAC G3 MODEL YEAR 2007. MODEL WAVE MODEL YEARS 2005-2010. DENALI MODELS MODEL YEARS 2007-2013. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/PONTIAC/SATURN: THERE MAY BE AN INTERMITTENT ENGINE HESITATION OR FLUTTER. THE CAMSHAFT SENSOR TERMINALS LIKELY HAVE POOR CONNECTIONS. *RM UPDATED 8/1/11. *PE UPDATED 4/16/12. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT; EVAPORATIVE EMISSION CANISTER PURGE SOLENOID VALVE WARRANTY. ON SOME MODEL YEAR CADILLAC VEHICLES, EQUIPPED WITH 3.6L V6 ENGINES (LY7) AND 2.8L V6 ENGINES (LP1), THE EVAPORATIVE EMISSION CANISTER PURGE SOLENOID VALVE MAY STICK OPEN OR CLOSED. IF THIS OCCURS, THE SERVICE ENGINE SOON LIGHT WILL ILLUMINATE. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC: SES LIGHT DUE TO DTC P1101; UPDATED ECM CALIBRATION FOR STS. SOME CUSTOMERS MAY EXPERIENCE A SES LIGHT ON COLD START WITH NO ENGINE PERFORMANCE CONCERNS. UPON INSPECTION, A P1101 DTC WILL BE FOUND WITH THE TECH 2. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6 LY7 WITH CAM ACTUATOR DTC. DTC CODES, P0016, P0017, P0018, P0019, P0008, OR P0009. *KB THE RELUCTOR FOR THE CRANKSHAFT SENSOR PRESSED ON THE CRANKSHAFT MAY HAVE MOVED. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INACCURATE FUEL GAGE READINGS, FUEL GAGE READS EMPTY WHEN THERE IS FUEL IN TANK, FUEL LEVEL LOW MESSAGE IN DIC, DTC P2066 SET (REPROGRAM ECM). WITH 2.8L OR 3.6L ENGINE (VINS T, 7 - RPO'S LP1, LY7). *NJ
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFORMATION ON REVISED GOODYEAR RS-A TIRE STYLE AND TPC NUMBER. VEHICLES BUILT AFTER AUG 15, 2007 OR VIN 80112115 ARE EQUIPPED WITH A REVISED VERSION OF THE EAGLE RS-A TIRE. *NJ