Original record summaries, dates and identifiers for this model-year. Records 201–300 of 337, ordered newest first. Dated records on this page: Dec 1, 2001–Mar 5, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 5, 2014Service Bulletin/Repair Instructions
PIT5264
NHTSA communication ID: 10111850
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Supplemental Inflatable Restraint lamp, Service Vehicle Soon lamp on and/or radio locked, possibly after module replacement. Technician will need to check for an incorrect or non-existent VIN number in modules that require them. Technician should ensure that all modules that are replaced are programmed per currently published Service Information. Technician should also check the Sensing and Diagnostic Module part number if it was replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: INFORMATION PROVIDED BY BULLETIN FOR ALL 2012 AND PRIOR GENERAL MOTOR TRUCKS AND PASSENGER VEHICLES REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK CHEVROLET GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. CSC LETTER WAS RECEIVED. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK CADILLAC CHEVROLET GMC HUMMER OLDSMOBILE PONTIAC SAAB SATURN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
L67 ENGINE OIL SMELL OR ODOR, LEAK AT LEFT OR FRONT VALVE COVER (REPLACE VALVE COVER GASKET, GROMMENTS AND SPARK PLUG WIRE RETAINERS FOR CYLINDERS 1-3-5). *NJ UPDATED 7/25/2008 *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WITH THE AC ON, LED APPEARS TO TOGGLE ON AND BACK OFF IN ONE UNIQUE CONDITION. THIS CONDITION IS THE HEADLAMPS ARE ON, INSTRUMENT PANEL LAMPS ARE DIMMED TO THE LOWEST EXTREME, DAYTIME CONDITIONS AND THE REAR DEFOG BUTTON IS TURNED ON AND OFF OR ALLOWED TIME TO TIMEOUT. ENGINEERING INVESTIGATED HAS DETERMINED THE CONDITION IS NORMAL. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES BUILT PRIOR TO VIN BREAKPOINT 1F136536 MAY EXHIBIT INTERMITTENT MALFUNCTION INDICATOR LAMP / SERVICE ENGINE SOON INDICATOR ILLUMINATION; ANTI-LOCK BRAKE SYSTEM WARNING LIGHT ILLUMINATION; STALL / NO START CONDITION; VARIOUS ELECTRICAL SYSTEM FAILURES; AND / OR VARIOUS DRIVEABILITY CONCERNS. *TT
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ENGINE SOON LIGHT ON WITH DIAGNOSTIC TROUBLE CODES P0716 AND / OR P0717, P0730, P0753, P0758, P1860, P1887 OR OTHER MISCELLANEOUS TRANSMISSION TROUBLE CODES SET. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
ENGINE COOLANT MAY LEAK AT THE UPPER INTAKE MANIFOLD THROTTLE BODY GASKET, OR AT THE UPPER INTAKE MANIFOLD TO LOWER INTAKE MANIFOLD TO LOWER INTAKE MANIFOLD GASKET. THIS CONDITION MAY RESULT IN A LOW ENGINE COOLANT LEVEL AND HIGHER ENGINE OPERATING TEMPERATURES. *TT THIS IS A PARTS BULLETIN AND REFERS TO CUSTOMER SATISFACTION PROGRAM BULLETIN #03034. *TT
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE VME MESSAGE IS TO PROVIDE INFORMATION ABOUT A NEW PRODUCT FIELD ACTION REGARDING A CUSTOMER SATISFACTION PROGRAM FOR AN ENGINE COOLANT LEAK. THE ENGINE COOLANT MAY LEAK AT THE UPPER INTAKE MANIFOLD THROTTLE BODY GASKET OR AT THE UPPER INTAKE MANIFOLD TO LOWER INTAKE MANIFOLD GASKET. *TT
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WIRE HARNESS MAY BE STRETCHED, OR THE PCS MAY NOT BE ORIENTED IN THE SAME POSITION, AFTER INSTALLING A SERVICE REPLACEMENT VALVE BODY ASSEMBLY. GM TECH LINK. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
ENGINE COOLANT MAY LEAK AT THE UPPER INTAKE MANIFOLD THROTTLE BODY GASKET, OR AT THE UPPER INTAKE MANIFOLD TO LOWER INTAKE MANIFOLD TO LOWER INTAKE MANIFOLD GASKET. THIS CONDITION MAY RESULT IN A LOW ENGINE COOLANT LEVEL AND HIGHER ENGINE OPERATING TEMPERATURES. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
CENTER CONSOLE AND/OR ARMREST STORAGE LID WILL NOT REMAIN CLOSED DUE TO A BROKEN LATCH. BOTH LATCHES ARE SERVICE SEPARATELY AND AVAILABLE THROUGH GM SERVICE PARTS. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ENGINE SOON LIGHT ON WITH DIAGNOSTIC TROUBLE CODES P0716 AND / OR P0717, P0730, P0753, P0758, P1860, P1887 OR OTHER MISCELLANEOUS TRANSMISSION TROUBLE CODES SET. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS BULLETIN PROVIDES INFORMATION ON TWO DIFFERENT CONDITIONS WITH THE TILT STEERING COLUMN STICKING THE EXTREME UP POSITION AND / OR STICKING IN THE NO.4 POSITION. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
VEHICLES WITH THE CJ2 AUTOMATIC AIR CONDITIONING AND WITHOUT THE U20 CLUSTER WHICH IS THE DRIVER INFORMATION CENTER AND THE CJ2 AUTOMATIC AIR CONDITIONER DISPLAYS THE CELSIUS AND NOT FAHRENHEIT. *TT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMMENT THAT THE SERVICE ENGINE SOON (SES) INDICATOR IS ILLUMINATED AND THAT WHILE THE LIGHT IS ILLUMINATED, TRANSMISSION SHIFTS ARE EXTREMELY HARSH. *TT