Original record summaries, dates and identifiers for this model-year. Records 1,301–1,400 of 1,405, ordered newest first. Dated records on this page: Sep 1, 2010–Dec 13, 2012.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Dec 13, 2012Service Bulletin/Repair Instructions
PIT4712D
NHTSA communication ID: 10112665
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the fuel gauge does not go to empty and the vehicle runs out of gas, or they may hear a fuel slosh or noise from the fuel tank area when braking or accelerating from a stop. Technician will need to inspect the fuel tank baffle for being loose.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Power Lift-gate, it will open fully, drop a few inches, then power close. Technician will replace the Lift-gate struts if it will not remain open when opened manually.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat, DTCs 5045 or B0074 0F May Set in PPS Module
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat, DTCs 5045 or B0074 0F May Set in PPS Module
NHTSA source summary · Original PDF not reviewed by Recallfolio
PASSENGER PRESENCE SYSTEM (PPS) MAY COMMAND PASSENGER AIRBAG INDICATOR AND SEAT BELT REMINDER ON WHEN ELECTRONIC DEVICES (COMPUTERS, MP3 PLAYERS, CELL PHONES, DIAGNOSTIC SCAN TOOL, ETC.) ARE PLACED ON FRONT PASSENGER SEAT, DTCS 5045 OR B0074 0F SET IN PPS MODULE. *JS UPDATED 2/21/13. *PE
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE · SEAT BELTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information in regards to all the porper towing weights and proper procedures that are in need of being completed to tow using the vehicles listed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information in regards to all the porper towing weights and proper procedures that are in need of being completed to tow using the vehicles listed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information in regards to all the porper towing weights and proper procedures that are in need of being completed to tow using the vehicles listed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the power lift gate Regular Production Option Code (E61 or TB5) is inoperative. Technician will find Diagnostic Trouble Code B153A set in the power lift gate control module. Technician will need to perform these steps. 1. Disconnect the connector at the Lift gate Latch Assembly. 2. Install a 3 ampere fused jumper wire between each signal circuit and the ground circuit. 3. If either test fails, check the wiring for the signal circuits, low reference circuit, or try a power lift gate control module from a known good vehicle. 4. If both tests pass, monitor the internal switch inputs in the lift gate latch assembly for proper operation. 5. If one of the internal lift gate latch assembly switch inputs are not reading correctly in one of the positions above and the vehicles passes test both test, replace the Lift Gate Latch Assembly.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:HATCHBACK/LIFTGATE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to set a personalized easy exit seat and/or power tilt column position and they will only move a predetermined amount. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information regarding a condition of the charging system light is illuminated and/or the Service Battery Charging System message is displayed, that might have been caused by oil being spilled into the generator while filling the engine oil level.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a list of corrections for multiple concerns regarding Unexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry Phone - Bluetooth Issues
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that when the remote start feature is used to start the vehicle, the Supplemental Inflatable Restraint light operation in the Instrument Panel Cluster varies depending on the model year. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A LIST OF CORRECTIONS FOR MULTIPLE CONCERNS REGARDING UNEXPECTED LOSS OF RADIO AUDIO (RADIO GOES SILENT/NO SOUND) AND OTHER BLACKBERRY PHONE - BLUETOOTH ISSUES
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure for the replacement of the camshaft cover for concerns relating to Malfunction Indicator Lamp (MIL) On, Poor Acceleration, Throttle Body Freezing, Multiple DTCs Set, Ice Deposits and/or Oil Deposits Present in Air Inlet Duct
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR THE REPLACEMENT OF THE CAMSHAFT COVER FOR CONCERNS RELATING TO MALFUNCTION INDICATOR LAMP (MIL) ON, POOR ACCELERATION, THROTTLE BODY FREEZING, MULTIPLE DTCS SET, ICE DEPOSITS AND/OR OIL DEPOSITS PRESENT IN AIR INLET DUCT
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure for the replacement of the sunroof sunshade stricker for the conditions of Front Sunroof Sunshade Will Not Latch or is Difficult to Latch in the Closed Position
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR THE REPLACEMENT OF THE SUNROOF SUNSHADE STRICKER FOR THE CONDITIONS OF FRONT SUNROOF SUNSHADE WILL NOT LATCH OR IS DIFFICULT TO LATCH IN THE CLOSED POSITION
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: SECOND AND/OR THIRD ROW BENCH SEAT CENTER BELT BUCKLE PLASTIC IS CRACKED. IT HAS BEEN FOUND THAT THIS COULD HAPPEN IF THE SECOND OR THIRD ROW SEAT IS FOLDED FLAT AND THE SEAT BELT IS STILL BUCKLED. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: FUEL GAUGE INOPERATIVE/FLUCTUATES HARD/NO START SES/CHECK ENGINE LIGHT ON. CONDITIONS MAY BE INTERMITTENT. UPON INVESTIGATION, THE TECHNICIAN MAY FIND VARIOUS DTCS SET. THIS CONDITION MAY BE DUE TO THE HARNESS RETAINER SLIPPING ON THE TUBING PUTTING PRESSURE ON THE HARNESS CAUSING CONNECTOR X305 TO BE PARTIALLY SEPARATED OR NOT FULLY SEATED. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET/GMC/SATURN: SQUEAK, MOAN OR RUB TYPE NOISE WHEN TURNING STEERING WHEEL AT SLOW SPEEDS. NOISE MAY BE DUE TO INSUFFICIENT GREASE IN THE PINION SHAFT SEAL. *PE UPDATED ON 5/2/2012. *KB
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/PONTIAC/SATURN: THERE MAY BE AN INTERMITTENT ENGINE HESITATION OR FLUTTER. THE CAMSHAFT SENSOR TERMINALS LIKELY HAVE POOR CONNECTIONS. *RM UPDATED 8/1/11. *PE UPDATED 4/16/12. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET/SATURN/BUICK: CLICK OR CLUNK NOISE FROM THE STEERING COLUMN WHEN TURNING. CAN BE DUPLICATED BY TURNING THE STEERING WHEEL BACK AND FORTH. MAYBE CAUSED BY A LOOSE RIVET ON THE LOWER STEERING COLUMN SUPPORT BEARING CAP. *PE UPDATED 4/6/12. *PE UPDATED 4/18/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC: CRANK NO START AFTER PARKING ON AN INCLINE WHEN FUEL LEVEL IS LOW. *PE UPDATED 6/8/10. *PE UPDATED ON 06/24/2011. *KB UPDATED 2/14/12. *PE UPDATED 4/4/12. *PE UPDATED 4/18/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/SATURN: INTERMITTENT UNWANTED LIFTGATE OR TRUNK OPENING, LIFTGATE OR TRUNK INOPERATIVE. TECHNICIAN MAY DETERMINE THAT THEY ARE UNABLE TO DUPLICATE THESE INTERMITTENT CONDITIONS. *PE UPDATED 3/12/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET/GEMS;SATURN: ON ALL WHEEL DRIVE VEHICLES, THERE ARE SOME CONCERNS OR ISSUES REGARDING INCIDENTAL SERVICE FOR THE NORMAL PROPELLER SHAFT CONDITIONS. *PE
Source components: POWER TRAIN:DRIVELINE:UNIVERSAL JOINT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THE FRONT PASSENGER AIRBAG INDICATOR MAY LIGHT WHEN ELECTRONICS ARE PLACED IN THE PASSENGER SEAT. THE ELECTRONICS CAUSE THE VEHICLE TO THINK THERE IS A PASSENGER SITTING IN THE SEAT. *RM UPDATED 6/24/11. *PE
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET/GMC/PONTIAC/SATURN/SUZUKI: ALL WHEEL DRIVE SYSTEM INOPERATIVE AND DTC C0550 SET. VARIOUS CONCERNS MAY BE RELATED TO A LOW BATTERY SUCH AS BUT NOT EXCLUSIVE TO A NO CRANK OR SLOW ENGINE CRANK CONCERNS OR MAY HAVE RECENTLY HAD TO HAVE THE VEHICLE JUMP STARTED. THIS MAY OCCUR DUE TO LOW VOLTAGE PRESENCE IN THE SYSTEM. *PE UPDATED ON 06/16/2011. *KB
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: ENGINEERING INFORMATION-CHEMICAL DAMAGE ON INNER SURFACES OF FUEL TANK. SOME CUSTOMERS MAY COMMENT ON POOR PERFORMANCE, DECREASED ACCELERATION AND/OR AN INOPERATIVE FUEL GAUGE. NO MODELS LISTED EXCEPT SATURN AND HUMMERS; INCLUDES ALL PASSENGER CARS AND LIGHT DUTY TRUCKS. *PE UPDATED 5/9/11. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET/GMC: MALFUNCTION INDICATOR LAMP (MIL) ON; DTC P0300, P0303, P0306, P062B, P0698, P0532, P0335, P0222 OR P0122 SET, ENGINE HARNESS CHAFFING. CONCERN MAY BE CAUSED BY ENGINE WIRING HARNESS MAKING CONTACT WITH BACK OF BANK 2 CYLINDER HEAD. *PE
Source components: ELECTRICAL SYSTEM:WIRING · ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PONTIAC/SATURN/BUICK/GMC/CHEVROLET/CADILLAC/HUMMER: VEHICLE START AND STALLS AFTER THEFT DETERRENT MODULE REPLACEMENT. MODEL YEARS 2006-2011. DOES NOT APPLY TO VEHICLES WITH KEYLESS ACCESS SYSTEM. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.