2015 BMW X5 Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 411, ordered newest first. Dated records on this page: May 1, 2015–Oct 1, 2016.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 1, 2016Service Bulletin/Repair Instructions
B652316
NHTSA communication ID: 10146902
NHTSA source summary · Original PDF not reviewed by Recallfolio
?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SHUDDER OR JERKING IN 7TH AND 8TH GEARS AT 1000 - 1400 RPM. A shudder or slight jerking can be felt when driving with the transmission in 7th or 8th gear and the engine speed is between 1,000 and 1,400 RPM. No related faults are stored and there are not any problems in the chassis systems or with the wheels and tires. This shudder or jerking could begin due to the characteristic power pulses of the N63T engine when it is in VVT mode at low engine loads.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HVAC BLOWER NOT WORKING This Service Information bulletin supersedes SI B64 12 16 dated August 2016. HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ENGINE SOON (MIL) - SME FC 21F20D. Malfunction Indicator Lamp (MIL) is illuminated. The following codes may be stored in the fault memory of the battery management electronics (SME). 21F20D - SME, safety concept: Switch-off of switch contactors by safety circuit 21F1F6 - High-voltage battery, switch contactors: Switch-off after a fault Software bug: erroneous fault code stored in SME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CLICKING NOISE FROM FRONT AXLE This Service Information bulletin supersedes SI 31 01 12 dated June 2015. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
NHTSA source summary · Original PDF not reviewed by Recallfolio
DDE FAULT CODE: 28DE00 - EXHAUST GAS PRESSURE SENSOR BEFORE TURBINE, PLAUSIBILITY. After performing repairs where the engine harness was disconnected and reconnected at the differential pressure and the exhaust pressure sensor, the following fault is then stored in the DDE: 28DE00 - Exhaust gas pressure sensor before Turbine, plausibility: exhaust gas pressure in front of turbine dynamically not plausible
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHECK CONTROL MESSAGE: NO OIL PRESSURE. Check Control message: Oil pressure warning. Stop carefully is displayed. There are no related faults to oil pressure stored in the DDE. Unfavorable DDE software application When operating during automatic engine start-stop function stop, it may be the case that the oil pressure is incorrectly determined to be too low, which triggers a CC message.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"INCORRECT TIRE AND LOADING INFORMATION LABEL. Five (5) vehicles were produced with an incorrect Tire and Loading Information label. The label may not reflect the proper ""Cold Tire Pressure"" specifications for the vehicle. AFFECTED VEHICLES Only the vehicles listed below are affected by this action: VINsMYModelCurrent Address State5UXKR0C5XF0K588942015X5 xDrive35iNew Jersey5UXKR0C57F0K588982015X5 xDrive35iFlorida5UXKR0C54F0K589072015X5 xDrive35iMassachusetts5UXKR0C58F0K589092015X5 xDrive35iNew York5UXKR0C5XF0K589132015X5 xDrive35iVirginia"
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HVAC BLOWER NOT WORKING. HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging Not Possible - KLE Fault 21E715. The following conditions may exist: Charging is either stopped mid-charge or will not initiate. The corona ring around the charge port blinks red. Check engine light is turned on. Faulty software up to and including ISTA/P 3.58.3 (F025-16-03-504)
NHTSA source summary · Original PDF not reviewed by Recallfolio
NOISE FROM THE FRONT SEAT WHEN ENTERING / EXITING THE VEHICLE. The front seats generate a squeaking noise upon entering or exiting the vehicle. The noise may also occur when repositioning on the seat or movement while driving. Aged/dried leather on the seat bottom cushion rubbing against the plastic side trim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAILGATE UNINTENTIONALLY OPENS. Trunk/tailgate may open when vehicle is locked. Trunk/tailgate may open while the vehicle is in motion. Usually after stopping, such as a traffic light etc. Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2"
NHTSA source summary · Original PDF not reviewed by Recallfolio
CLICKING NOISE FROM FRONT AXLE This Service Information bulletin supersedes SI 31 01 12 dated June 2015. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Source components: BACK OVER PREVENTION · EQUIPMENT · SUSPENSION:FRONT:WHEEL BEARING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diesel Engine: Intake Manifold Damaged This Service Information bulletin supersedes SI 11 07 16 dated May 2016. The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N63T PRESSURE SWITCH - LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the above-referenced vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N55 PRESSURE SWITCH - LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the eligible vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ticking Noise from the Front Axle When Cornering This Service Information bulletin supersedes SI B34 05 15 dated December 2015. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a metallic ticking from the area of the front wheels. Movement between the inner contact surfaces of the brake disc and drive flange of the wheel bearing hub.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
NHTSA source summary · Original PDF not reviewed by Recallfolio
"BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Program Variable Damper Control (VDC) Unit. Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diesel Engine: Intake Manifold Damaged. The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"""Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
NHTSA source summary · Original PDF not reviewed by Recallfolio
Airbag (SRS) Warning Lamp Illuminated. Airbag lamp (SRS) is illuminated and both of the following fault codes are stored: 930904 - Airbag driver stage 1: Resistance too large 93090A - Airbag driver stage 2: Resistance too large CAUSE Coil spring cassette damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Crackling Noise from the Fresh Air Grille This Service Information bulletin supersedes SI B64 05 16 dated March 2016.. Customer complains of crackling noises coming from the fresh air grille for approx. 15 seconds when switching on the air-conditioning system. Refrigerant transition inside the evaporator.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Incomplete AdBlue Check Control Message (CCM) on the Central Information Display. An incorrectly displayed AdBlue (Diesel Exhaust Fluid refill range) CCM is shown on the Central Information Display. Improper instrument cluster software
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging Not Possible - KLE Fault 21E693. The following conditions may exist: Charging is either stopped mid-charge or will not initiate. The corona ring around the charge port blinks red. Check engine light is turned on. Faulty software up to and including ISTA/P 3.58.3 (F025-16-03-504)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Passenger Side Mirror Dimming Feature Operational Change. INFORMATION The automatically dimming exterior mirror function on the passenger's side has been deleted from the Option Code 430 as noted above. The automatic dimming function will continue to be operational on the driver's side mirror and rear view mirror.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"F15, F30 PHEVs- Gear Selector Plausibility Faults. The Check Control message ""Drive: Stop carefully"" (CCM-ID: 569) is displayed. The following fault codes may be stored in the transmission EGS control module (GKEG3HY3): 44D663 - Position plausibility: Driver's choice N/P from D/R not executed CF1701 - Gear selector switch interface, communication failure CF17A1 - Message missing: receiver EGS (A-CAN), transmitter selector switch (A-CAN) EGS software diagnostic function"
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Delivery Stop - Transmission Oil Cooler Lines Incorrectly Routed. A Delivery Stop has been issued for fifteen F15 vehicles produced from March 3, 2016 to March 28, 2016. In these vehicles the cooler lines for the automatic transmission may have been routed incorrectly. In such instances, the cooler lines may come into contact with the crankshaft vibration damper (pulley). Affected vehicles can be identified with a ""Vehicle Comment"" in DCS Warranty Vehicle Inquiry or ISPA Light with the description: ""A Delivery Stop has been issued for this vehicle. Dealers must ensure that all Campaigns are completed before retail delivery to the customer. See Service Information Bulletin B17 01 16."""
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N63, N63TU and N63R Engines: Upper Oil Pan Removal and Installation Repair Instructions This Service Information bulletin supersedes SI B11 17 15 dated August 2015.. INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.11 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. The low washer fluid warning light is illuminated even though the washer fluid tank is full. There are no faults stored in the system for the washer fluid level switch. CAUSE A non-approved washer fluid is used (fluids that contain a silicone additive, normally colored other than blue). INFORMATION The washer fluid level sensor is a contactless capacitive sensor. The sensor sends a low fluid level signal to the gateway module (FEM - Front Electronics Module or BDC - Body Domain Controller) which in turn displays a low washer fluid warning in the instrument cluster. The use of a ""non-approved"" washer fluid (silicone-based fluid) can cause the low fluid warning light to come on even when the reservoir is full. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"""Comfort Access Restricted"" Check Control Message is Displayed. ""Comfort Access Restricted"" CCM (Check Control Message) is permanently displayed.. The CCM ID: D0h. The comfort access is functioning correctly. No comfort access aerial fault codes stored in the BDC (Body Domain Controller). Software error in the BDC"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NBT-EVO Head Unit Cannot Be Swapped Between Vehicles for Testing. If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called ""Trusted VIN"""
NHTSA source summary · Original PDF not reviewed by Recallfolio
NBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
NBT Head Unit Aborts Import of CD. While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
"False Alarms of the Anti-Theft Alarm System. The alarm (DWA) siren continues to activate after locking vehicle An ""unapproved"" device is connected to the On-Board Diagnostics (OBD) port of the vehicle. This keeps the Ethernet communication line active which triggers the alarm when the vehicle tries to enter sleep mode."
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Crackling Noise from the Fresh Air Grille. Customer complains of crackling noises coming from the fresh air grille for approx. 15 seconds when switching on the air-conditioning system. Refrigerant transition inside the evaporator.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Air Conditioning Refrigerant R1234yf Introduction. Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B36 01 15 February 2016 Wheel and Tires Technical Service This Service Information bulletin supersedes SI 36 01 15 dated October 2015. designates changes to this revision SUBJECT Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Source components: EQUIPMENT · TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The DDE software application for exhaust gas recirculation control (EGR) does not favorably match the diesel fuel grades available in many parts of the US market. The high pressure EGR cooler could become filled with soot particulate to the point that exhaust gas flow and cooling efficiency are significantly reduced. This could result in the Service Engine Soon light coming on with EGR control / Air mass faults being stored in the DDE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain engine operating conditions the measured air mass between the cylinder banks 1-4 and 5-8 is miscalculated by the DME's. This could result in incorrect engine torque and mismatched ignition parameters with the possibility of internal engine damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?This Service Information bulletin supersedes SI B65 13 13 dated October 2014. SUBJECT Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed . Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Note: If Fault Code E1C440 ""Headunit Reset"" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Instrument Cluster Multifunction Display Intermittently Blank . Some information displays in the Instrument Cluster (KOMBI) may intermittently go blank. This may include the tachometer and speedometer displays. There is a software error in the KOMBI.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Vehicles which have had the Instrument Cluster (KOMBI) replaced may display incorrect CBS (Condition Based Service) data after programming. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Incorrect SW calibration loaded after KOMBI replacement."
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B61 30 14. January 2016. General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 30 14 dated December 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure . INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B16 15 14 January 2016 Fuel Supply Systems Technical Service.This Service Information bulletin supersedes SI B16 15 14 dated December 2014, designates changes to this revision. SUBJECT NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak . The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm. CAUSE: Contamination of the NVLD pressure switch diaphragm and/or the contamination of the NVLD dust filter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Instrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?SI B61 30 14December 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated July 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. INFORMATION The use of a ""non-approved"" washer fluid can cause the low fluid warning light to come on even when the reservoir is full. An analysis of parts returned to warranty has shown the sensor is operating correctly. Do not replace the reservoir with integrated sensor for these situations. We recommend using ""BMW Group approved"" washer fluid when servicing the vehicle or performing repairs on the windshield washer system. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates. If the correct washer fluid is being used, diagnose the system using normal troubleshooting with ISTA. A fault code may be stored if an electrical fault occurs in the circuit. PARTS INFORMATION Part NumberDescriptionQuantity83 19 2 406 220BMW WWS Cold Weather Concentrate 35% 55 GalAs needed83 19 2 361 205BMW Windshield Washer Concentrate 1 GalAs neededNote: As applicable, do not exceed your state's maximum for the allowable amount/percentage of ""Washer Concentrate"" that can be used when mixing the windshield washer fluid solution. WARRANTY INFORMATION The issue described in this bulletin is not a vehicle-related defect in materials or workmanship. If a vehicle repair is required as a result of this issue, it is are not claimable under a BMW limited warranty."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Sunroof Makes a Creaking Noise During Operation. When opening or closing the sunroof a creaking/ crackling type noise is heard. Insufficient lubrication of the sunroof guide rails
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ticking Noise from the Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a metallic ticking from the area of the front wheels. Movement between the inner contact surfaces of the brake disc and drive flange of the wheel bearing hub.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SI B13 10 15 Fuel Systems December 2015 Technical Service. This Service Information bulletin replaces SI B13 07 15 dated August 2015. The DDE software release for the Engine Start-Stop (MSA) function is incomplete. As a result the (MSA) feature cannot be activated with the MSA On/Off switch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Comfort Access Does Not Function After Vehicle Enters Sleep Mode. Sporadically, when the vehicle has been locked and is in sleep mode, the vehicle will not waken when trying to unlock the vehicle with comfort access from any door. The vehicle can be unlocked from the remote. After waking, the comfort access function is restored. Software fault in the BDC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Instrument Cluster display is partially blank. INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Encoding If a control module was working properly and it fails to program correctly or requires initialization, please claim this additional work with the applicable KSD2 labor operations under the defect code listed above. The diagnosis and repair of vehicles ""arriving"" with failed control modules or stored faults which will cause them to fail during programming cannot be claimed under the defect code listed in this bulletin. Other Repairs If other eligible and covered work is performed ""prior"" to programming and coding the vehicle, claim this work with the applicable defect code and labor operations listed in KSD2. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
Leaking Rear Differential (QMVH). There is an oil leak from the rear differential housing. The liquid-type sealer used between the main differential housing and the outer superimposing gear units has failed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Instrument Cluster display is partially blank. The Instrument Cluster (Kombi) lower display may be intermittently blank. The Board Computer, Ambient Temperature and Check Control Messages will not display. Instrument Cluster software error.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Third Row of Seats Blower is Inoperative. The blower in the third row of seats is not working and the fault code ""E70C32 - AC-LIN: Heating in third row of seats is not responding"" has been entered in the IHKA (Integrated Heating and Airconditioning, Automatic) control unit. CAUSE LIN BUS short or open circuit in wiring or connectors Blower motor, micro switch defective Control unit, A/C, for 3rd seat row defective."
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER · SEATS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. CAUSE When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR · STEERING:COLUMN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI 37 02 14 dated February 2015. Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
Source components: SERVICE BRAKES, HYDRAULIC · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
Source components: POWER TRAIN:DRIVELINE · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N57T - Automatic Start/Stop (MSA) Does Not Function. The MSA feature to shut the engine off does not function at any time, although it is set to active. The MSA test plan indicates that the ""engine stop"" inhibitor is currently active due to missing steering angle information. There are no relevant faults stored and the steering angle is calibrated correctly. CAUSE A communication error between the engine (DDE) and electronic steering (EPS) control units."
NHTSA source summary · Original PDF not reviewed by Recallfolio
After Cold Start, Brake Booster Reservoir Vacuum Reduced. With an outside temperature below 14ºF, brake booster vacuum may be reduced after a cold start. The non-return valve in the vacuum line to the brake booster may stick at temperatures below 14ºF. Sufficient vacuum supply is available again at the brake booster only after the vehicle is driven (approximately 1/4 mile).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N57T - Automatic Start/Stop (MSA) Does Not Function. The MSA feature to shut the engine off does not function at any time, although it is set to active. The MSA test plan indicates that the ""engine stop"" inhibitor is currently active due to missing steering angle information. There are no relevant faults stored and the steering angle is calibrated correctly. CAUSE A communication error between the engine (DDE) and electronic steering (EPS) control units."
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Seat Heater Inoperative. The front passenger and both rear seat heaters do not work. The following fault codes are stored in the BDC (Body Doman Controller): D90C18 - LIN master I: Short circuit D90C1A - LIN master I: Communication faulty CAUSE One of the rear seat heater modules has an internal fault, which interrupts LIN bus communication.
Source components: ELECTRICAL SYSTEM · SEATS · SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
Source components: POWER TRAIN:AXLE ASSEMBLY · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC · WHEELS:HUB.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Noise When Adjusting the Steering Column Up or Down. Creaking noise when raising or lowering the steering column position CAUSE Steering column adjustment
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Reduced Engine Power with ""Charging Pressure Too High"" Faults Stored. When accelerating under certain conditions, the engine power may be reduced and a Check Control Message (CCM) ""Drive Faulty; Drive at moderate speed"" is displayed. The following charging pressure control fault is stored in the DME: ? Fault 120208: Exhaust camshaft sensor, signal: not plausible As a result, the engine power is reduced, and the following faults may also be set: ? Fault 120408: Charging pressure control: Switch-off, pressure build-up blocked ? Fault 120908: Charging pressure control2: Switch-off, pressure build-up blocked CAUSE DME software error"
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHECK CONTROL MESSAGE (CCM) "DRIVE FAULTY; DRIVE AT MODERATE SPEED" WILL DISPLAY AND ENGINE POWER MAY GO DOWN WHEN ACCELERATING UNDER CERTAIN CONDITIONS DUE TO DME SOFTWARE ERROR. *MA
NHTSA source summary · Original PDF not reviewed by Recallfolio
"BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: SOME VEHICLES EXPERIENCING THE FAILURE OF TIRE PRESSURE MONITOR (RDCI) DUE TO REMOTE CONTROL UNIT HARDWARE (FBD3 ANTENNA) AND NEEDS REPAIRING. MODEL YEARS 2014-15. *PE
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Makes Unusual Whistling Noise from Center Vents. An unusual whistling noise can be heard coming from the center vent area for approximately15 seconds after the A/C is switched on. CAUSE Evaporator in the A/C system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.