2015 BMW X3 Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 305, ordered newest first. Dated records on this page: Feb 1, 2014–Sep 1, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 1, 2015Service Bulletin/Repair Instructions
B840315
NHTSA communication ID: 10147271
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HU-B: Bluetooth Connection Fails Sporadically. The Bluetooth system works intermittently. One or more of the following scenarios may occur: Bluetooth pairing is not possible - display shows ""Please wait"" Unable to select the check box to activate Bluetooth Device does not reconnect to the vehicle after a key cycle Audio interference noise is heard listening to iPod etc. When trying to access the user manual, the display shows ""Please wait"" Incorrect software installed in the HU-B (Headunit Basic)."
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The AUC (Automatic Recirculation Sensor) is installed pointing upwards instead of downwards. The AUC becomes contaminated. AFFECTED VEHICLES This Service Action involves F25 (X3) and F26 (X4) vehicles produced from July 31, 2015 to August 25, 2015. ONLY 41 vehicles are involved. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. CAUSE When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR · STEERING:COLUMN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"This Service Information bulletin supersedes SI B51 29 15 dated August 2015.. Both rear side ""fixed"" windows need to be replaced due to incorrect glue application, this may cause a water leak. AFFECTED VEHICLES This Service Action involves F25 (X3) and F26 (X4) produced from July 13, 2015 to July 14, 2015. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
Source components: POWER TRAIN:DRIVELINE · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. Engine oil leakage into the induction system and/or the turbo charger assembly.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Delivery Stop: Rear Side Window. Delivery Stop has been issued on vehicles produced from August 13, 2015 through August 14, 2015. These vehicles may have had the rear side window adhesive incorrectly applied. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at ports of entry will be repaired prior to dealer delivery. This bulletin will be updated with instructions and warranty information when it becomes available. Please contact your field representatives if you have any questions. The affected vehicles can be identified with a ?Vehicle Comment? in DCS Warranty Vehicle Inquiry or ISPA Light with the description: ? Defect Code 0051760300, Delivery Stop, Rear Side Window, see SI B51 29 15.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tailgate intermittently cannot be opened or closed. One or more of the following situations can occur, if the tailgate striker is not adjusted properly: ? The tailgate does not lock ? The tailgate does not remain locked ? The tailgate does not close ? The tailgate does not remain closed ? The tailgate does not open CAUSE The tailgate lock striker is not adjusted correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Deformation of the Fuel Tank. The vehicle loses power while driving. There may also be a complaint of difficulty refilling the tank. CAUSE There is inadequate venting of the fuel tank. This results in a lack of pressure compensation (vacuum) in the fuel tank as the level drops which causes the tank to collapse.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Message with Rear Light Failure. Intermittently, a Check Control Message (CCM) is displayed for one or more rear light failures: ? Rear light ? Brake light ? Rear indicator One or more fault codes are registered in the Footwell Module (FRM) for one or more circuits with the fault not currently present: ? 800F46 - Indicator rear left defective ? 800F47 - Indicator rear right defective ? 800F56 - Brake light left defective ? 800F57 - Brake light right defective ? 800F80 - BFD left defective ? 800F81 - BFD right defective ? 802812 - Brake light / direction indicator, left: light faulty or open circuit ? 802813 - Brake light / direction indicator, right: light faulty or open circuit ? 800F7A - Reversing light left defective ? 800F7B - Reversing light right defective CAUSE Bad connection at the rear light in the tailgate and/or rear light in the side panel
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: DUE TO ONE OR MORE REAR LIGHT FAILURES, THE CHECK CONTROL MESSAGE (CCM), INTERMITTENTLY WILL BE DISPLAYING BRAKE LIGHT, REAR INDICATOR, AND/OR REAR LIGHT. MODEL F25. *PE UPDATED 9/25/15. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Program Control Units (SCR). The Selective Catalyst Reduction (SCR) control module can make an error when calculating the DEF line pressure. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N20 and N26 Engines: ETK Injector Part Number Error. INFORMATION The current version of ETK has an error on screen 13_1417: ""High -pressure pump/Tubing."" When selecting the high-pressure pump, the screen states ""only in conjunction with injector."" Disregard this statement and only replace the high-pressure pump. If injectors need to be replaced, enter the VIN of the vehicle into the ETK and select the part numbers found on screen 13_1416: ""High-pressure rail/injector/mounting."" Always enter the VIN for the vehicle into ETK when searching for parts. When the ETK is corrected, this SIB will be updated. WARRANTY INFORMATION Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/224...5/4/2015"
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: ? 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: FUEL GAUGE FAILS TO SHOW CORRECT LEVEL OF FUEL WHEN FILLING FUEL TANK BUT WOULD UPDATE ITSELF AFTER DRIVING AWHILE AND ILLUMINATION OF ENGINE MALFUNCTION LAMP (MIL) COMES ON, DUE TO SOFTWARE ERROR IN INSTRUMENT CLUSTER. MODEL 2011-15. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Heating and Air Conditioning March 2015 Technical Service This Service Information bulletin supersedes SI B64 03 14 dated March 2015. designates changes to this revision SUBJECT A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: DUE TO TRANSMISSION OIL HEAT EXCHANGER'S FAULTY THERMOSTAT OR ENGINE FAULTY CHARACTERISTIC MAP THERMOSTAT, ENGINE COOLANT FAILS TO REACH OPERATING TEMPERATURE, WITH LOW HEAT OUTPUT AND SERVICE ENGINE SOON LIGHT COMES ON. NO MODEL YEARS LISTED. *PE
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT Service Action: Program Control Units (SCR). An error in the calculation of the DEF line pressure by the SCR module software could occur at temperatures below 32°F/0°C. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"MSUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the ""Attachment"" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 24 13 dated January 2014. designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B16 16 14January 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B16 16 14 dated December 2014. designates changes to this revision SUBJECT Service Engine Soon Light (MIL) Is On with SCR Faults Stored. The Service Engine Soon light is on with the following fault stored in the Selective Catalyst Reduction module (SCR). z 805220 - Delivery module, system pressure, pressure build-up is too low. This fault is very likely to be stored at temperatures below 32°F / 0°C if the vehicle is programmed using ISTA/P 3.54.1 or 3.54.2. F25 (X3) only: z 8051B0 - Metering line heating, power too high SCR module software error
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B13 02 14January 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B13 02 14 dated September 2014. designates changes to this revision SUBJECT N47T: Diesel Particulate Matter Sensor Faults Stored in DDE. Either of the following situations could occur: The Service Engine Soon lamp (MIL) is on with any of the following diesel particulate matter (PM) sensor faults stored: z 2BB700 - Particulate sensor, plausibility: Sensor protective pipe plugged z 2BB600 - Particulate sensor, diagnosis response: Measuring electrode, bypass detection z 2BB300 - Particulate sensor, diagnosis response: Measuring electrode, self-diagnosis z 2BA100 - Particulate sensor, diagnosis response: Temperature measurement, electrical fault These stored faults would not cause a problem with engine performance. Or, The PM sensor has come loose or has fallen out of the exhaust. DDE software diagnosis sensitivity and PM sensor hardware
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B12 35 14 dated December 2014. designates changes to this revision SUBJECT N20, N26 Service Engine Soon Light On: Fault Code 1B9702 is Stored. The Service Engine Soon light (MIL) is on with only the following fault stored in the DME: z 1B9702: Engine switch-off time, timer, instrument panel timer DME, Comparison: Value of instrument panel timer too low while engine is running This fault will not cause any engine running or drivability problems. Instrument cluster software error.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the ""fuel consumption, current"" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold."
Source components: VEHICLE SPEED CONTROL · VEHICLE SPEED CONTROL:ACCELERATOR PEDAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: z 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT Deleting DME Adaptations After Crankshaft Sensor-related Repairs. The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement of the crankshaft position sensor 2. Replacement of the incremental sensor wheel on the crankshaft 3. Replacement of the crankshaft 4. Replacement of the crankcase (block) with pistons 5. Replacement of the engine assembly Due to slight tolerance differences with the new replacement hardware and the original learned crankshaft position, values could cause cylinder balance calculation errors by the DME. DME software (the incremental wheel adaptation cannot be cleared)
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this service action to be completed prior to customer delivery.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Central Information Display Intermittently Flashes Off/On. Intermittently, the Central Information Display (CID) flashes off/on. Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Automated Activation of Navigation System During PDI/QC1. INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system. Note: This VIN-specific NAV enabling code is then also automatically stored in the Repair Kit in the Aftersales Assistance Portal (ASAP). The automated INITIAL NAV enabling code request and activation of the navigation system will take no longer than 1 minute. After finishing "Delete Transport Mode," the navigation system in the vehicle will be active without entering the 20-digit INITIAL NAV enabling code manually or in ISTA. If the navigation system is not active and asking for the enabling code, turn off the ignition and wait for the head unit to enter sleep mode (approx. 3 minutes). After that, turn on the ignition again. The head unit will start up and the navigation system is activated. If the INITIAL NAV enabling code for first-time activation of the navigation system is not requested or delivered automatically, it still can be ordered manually through the Parts department and activated in the vehicle through the iDrive controller, by entering the 20-digit enabling code manually.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Controller Responds Slowly or Not at All. When the customer presses or turns the controller, there is no or a delayed response. This can sporadically occur. Software in the controller
NHTSA source summary · Original PDF not reviewed by Recallfolio
Dual Mass Flywheel - Diagnosis and Inspection. INFORMATION The following three criteria must be checked, evaluated and the resulting findings documented on the repair order prior to replacing a dual-mass flywheel as defective: 1. Total rotational angle at no load condition (with applied torque less then 20 Nm) 2. Secondary plate longitudal axial play 3. Friction surface appearance changes due to thermal overload.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Engine Soon Light (MIL) is On with SCR Fault 805220 Stored. The Service Engine Soon light is on with the following fault stored in the Selective Catalyst Reduction module (SCR). z 805220 - Delivery module, system pressure, pressure build-up is too low. This fault is very likely to be stored at temperatures below 32°F / 0°C if the vehicle is programmed using ISTA/P 3.54.1 or 3.54.2. Unfavorable SCR software
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20, N26 Service Engine Soon Light On: Fault Code 1B9702 is Stored. The Service Engine Soon light (MIL) is on with only the following fault stored in the DME: ? 1B9702: Engine switch-off time, timer, instrument panel timer DME, Comparison: Value of instrument panel timer too low while engine is running This fault will not cause any engine running or drivability problems. Unfavorable instrument cluster and DME software
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Intermittently Will Not Start at Very Low Outside Temperatures. The engine will not start at times at very low outside temperatures (-4°F/-20°C and colder); however, the battery state of charge is correct and the starter turns the engine over properly. This starting difficulty is most likely to occur after shutting the engine off briefly for 5 or 10 minutes, such as when refueling. The following faults are most likely stored in the DME: N20 engine: ? 1B5202 - Terminal 15N_1: No voltage? 1B5302 - Terminal 15N_2: No voltage ? 1B5402 - Terminal 15N_3: No voltage N52T engine: ? 1B5102 - Terminal 15N_3: line from CAS, electric: short circuit to earth ? 1B5501 - Terminal 15N: No voltage ? 1F0601 - Terminal 15N from CAS, switching delay: Switches too lateN55 engine: ? 1B5202 - Terminal 15N_1: No voltage? 1B5302 - Terminal 15N_2: No voltage ? 1B5402 - Terminal 15N_3: No voltage In addition, other engine electronic power supply-related faults could be stored for components such as VANOS solenoids, camshaft sensors, engine oil pressure sensor, engine oil pressure control valve, engine oil level sensor, etc. At very low outside temperatures, low levels of moisture present inside the power distribution module (PDM) can freeze the internal micro-relay contacts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vehicle inTransport Mode Cannot Be Unlocked with Remote Control. When the vehicle is in transport mode, intermittently it cannot be unlocked via the remote control key. CAUSE When the vehicle is in transport mode, to reduce power consumption, the software is designed to disable the outside antenna receiver from waking up the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B64 03 14 dated October 2014. designates changes to this revision SUBJECT A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Message with Rear Light Failure. Intermittently, a Check Control Message (CCM) is displayed for one or more rear light failures: z Rear light z Brake light z Rear indicator One or more fault codes are registered in the Footwell Module (FRM) for one or more circuits with the fault not currently present: z 800F46 - Indicator rear left defective z 800F56 - Brake light left defective z 800F57 - Brake light right defective z 800F81 - Adaptive brake light, right, faulty z 802812 - Brake light / direction indicator, left: light faulty or open circuit z 802813 - Brake light / direction indicator, right: light faulty or open circuit CAUSE Bad connection at the rear light in the tailgate and/or rear light in the side panel
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · STRUCTURE:BODY:TAILGATE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B51 33 14 dated October 2014. designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.
NHTSA source summary · Original PDF not reviewed by Recallfolio
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H
NHTSA source summary · Original PDF not reviewed by Recallfolio
LED Low Beam Flashes Briefly After Ignition Switched ON. 1. The low beam flashes briefly after the ignition is switched ON. This situation can be duplicated every time the vehicle is started. 2. One of the faults below is stored and currently present: 0xDA1411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC 0xD9D411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC Faulty LED main light module (LHM2)
NHTSA source summary · Original PDF not reviewed by Recallfolio
LED Headlight Malfunction. 1. The LED headlight on one side malfunctions. 2. One headlight flickers on and off while driving (problem is sporadic). 3. The Check Control message indicates the parking light or driving light is defective. One or more of the following faults can be stored: 805980 Low-beam headlight defective 805981 High-beam headlight defective 8044BB Right-hand LED main light module (LHM2) implausible low-beam headlight function status 8044BA Left-hand LED main light module (LHM2) implausible low-beam headlight function status CAUSE The situation above is caused by a poor connection at the LED headlight connector or LED main light module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
. INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Delivery Stop: Crankcase Failure. A Delivery Stop has been issued on certain 2015 model year vehicles with N20/N26 engines produced from September 4, 2014 through October 21, 2014. These vehicles may have a crankcase failure. Approximately 145 vehicles are affected.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Engine Soon Lamp (MIL) On with NOx Sensor Faults Stored. The Service Engine Soon lamp (MIL) is on with either of the following nitrogen oxide (NOx) sensor faults stored: * 2B6200 - NOx sensor before DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity * 2B6300 - NOx sensor After DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity These stored faults would not cause a problem with engine performance. This NOx self-diagnostic routine is performed only after the engine has been shut off. In some situations, the diagnostic function of both NOx sensors can be too sensitive when sampling the residual exhaust gases, leading to an erroneous fault being set. Unfavorable DDE software diagnostics
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Service Engine Soon lamp (MIL) is on with any of the following diesel particulate sensor faults stored: * 2BB700 - Particulate sensor, plausibility: Sensor protective pipe plugged * 2BB600 - Particulate sensor, diagnosis response: Measuring electrode, bypass detection * 2BB300 - Particulate sensor, diagnosis response: Measuring electrode, self-diagnosis * 2BA100 - Particulate sensor, diagnosis response: Temperature measurement, electrical fault These stored faults would not cause a problem with engine performance. Unfavorable DDE software
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL · EQUIPMENT:OTHER:LABELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 and N26 Injector Replacement. INFORMATION When a defective high-pressure fuel injector is identified with an index "02" designation, as shown in the illustration below, all 4 injectors must be replaced at the same time. This bulletin only applies to index "02" injectors. Index "01" and index "03" or higher are not affected. No immediate repair is required unless the BMW vehicle is currently experiencing this problem.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When Unlocking with Comfort Access the Outside Door Mirrors Are in the Wrong Position. The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module
NHTSA source summary · Original PDF not reviewed by Recallfolio
Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various Electrical Faults Caused by Shorted K-CAN2. One or more of the following situations can occur when the K-CAN2 wiring in the vehicles is shorted. ? There is no communication with any K-CAN2 control modules during an ISTA vehicle test. The following control modules are on the K-CAN2: ZGM - Central Gateway Module FRM - Footwell Module CAS - Car Access System Headunit - Radio/Navigation ComBox/TCB - Telematic Control Module FZD - Roof Function Center Module JBE - Junction Box Electronics * The transmission will not engage a gear when with the engine running. * The vehicle sporadically does not start. * In rare cases, the vehicle may stop running while driving. When the K-CAN2 is shorted, the vehicle will store many line and communication faults for the K-CAN2, including the following: * JBE - C9140D No message, receiver JBE, transmitter CAS * JBE - C90468 K-CAN2; Communication fault * ZGM - CD0468 K-CAN2: Communication fault * ZGM - CD1400 Message incorrect, receiver ZGM, transmitter JBE * CAS -D9045F K-CAN2: Line fault * CAS - D90468 K-CAN2: Communication fault * FZD - DE8468 K-CAN2: Communication fault * TCB - E14468 K-CAN2: Communication fault * TCB - E1445F K-CAN2: Line fault * NBT - E1C468 K-CAN2: Communication fault * FRM - E5845F K-CAN2: Line fault * FRM - E58468 K-CAN2: Communication fault The wiring harness gets pinched between the instrument panel and the locating tab on the passenger side of the instrument panel. K-CAN2 High - GE/RT (Yellow/Red) K-CAN2 Low - GE/BR (Yellow/Brown).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Engine Soon Lamp (MIL) On with NOx Sensor Faults Stored. The Service Engine Soon lamp (MIL) is on with either of the following nitrogen oxide (NOx) sensor faults stored: * 2B6200 - NOx sensor before DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity * 2B6300 - NOx sensor After DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity These stored faults would not cause a problem with engine performance. This NOx self-diagnostic routine is performed only after the engine has been shut off. In some situations, the diagnostic function of both NOx sensors can be too sensitive when sampling the residual exhaust gases, leading to an erroneous fault being set. Unfavorable DDE software diagnostics
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: IN SOME VEHICLES, WHEN THE K CAN2 WIRING IS SHORTED, NO COMMUNICATION WITH ANY CONTROL MODULES (BOX ELECTRONICS, TELEMATIC CONTROL MODULE,CAR ACCESS SYSTEM, RADIO/NAVIGATION, CENTRAL GATEWAY MODEL OR FOOTWELL MODULE) DURING VEHICLE TESTING, NO ENGAGEMENT OF TRANSMISSION GEARS, FAIL TO START, WHEN DRIVING, WILL STOP RUNNING. MODEL F25 (X3). *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering Wheel Vibration Level Is Unacceptable. The vibration level produced by the steering wheel vibration actuator is too strong or too weak. This is only noticed when Lane Departure Warning (LDW) is triggered. CAUSE Vibration actuator in the steering wheel
Source components: LANE DEPARTURE · STEERING · SUSPENSION · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
iPhone Charging Status Constantly Switches On and Off. INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Airbag Warning Light: ACSM FC 930A60 Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Wheel Speed Sensor Failure. The Check Control Message displays: ""Driving stabilization, continue driving at a moderate speed. Avoid abrupt braking as far as possible."" Drive to the nearest BMW Service Center. Also ""TPM (Tire Pressure Monitor) failed"" may be displayed. One or more of the following fault codes are stored in the DSC (Dynamic Stability Control) module regarding wheel speed sensor failure: 480A90,480715,48071B,480712,480718,480717,48071A,4809B0,4809B9,480686 4809CD,480AAA,480AB1,480AB4,480AAD,480A9F,480AA3,480A9C,480AA6,480710 480713,480AAC,480719,480A9E,480AB3,480AA5,480716,4809B7,480928,4809C2 480711,480714,4809CB,480AAB,480AB2 Front/rear wheel speed sensor"