2018 BMW X1 Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–98 of 98, ordered newest first. Dated records on this page: Nov 1, 2017–Jun 26, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 26, 2026Warranty Program/Extension
B010224
NHTSA communication ID: 11035496
NHTSA source summary · Original PDF not reviewed by Recallfolio
The EVAP systems purge (vent) valve limited warranty for defects in materials and / or workmanship has been extended to 15 years / 150,000 miles as determined from the original first in-service / delivery date.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The EVAP systems purge (vent) valve limited warranty for defects in materials or workmanship has been extended to 15 years / 150,000 miles as determined from the original in-service date.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Telematics Control Units (TCU) Internal Emergency (Backup) Battery for defects in materials and/or workmanship has been extended to 6 years without mileage limitation, as determined from the vehicles original first in-service / delivery date. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Telematics Control Units (TCU) Internal Emergency (Backup) Battery for defects in materials and/or workmanship has been extended to 6 years without mileage limitation, as determined from the vehicles original first in-service / delivery date.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The “End of life” or “Emergency call system error” Check Control message appears in the vehicle. The following fault memory entry is stored: B7F341 – Emergency battery: Hardware faulty
NHTSA source summary · Original PDF not reviewed by Recallfolio
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer states one of the front seats is inoperative. The seat heater and power supply are inoperative. During the vehicle test, the seat module does not respond. The power supply fuse for the seat module isfound to have blown.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer states one of the front seats is inoperative. The seat heater and power supply are inoperative .During the vehicle test, the seat module does not respond. The power supply fuse for the seat module is found to have blown.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When using the Key Reader to retrieve CBS information from the customer key, no current vehicle data is available, or the data does not match the maintenance schedule.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicleâÂÂs equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When using the Key Reader to retrieve CBS information from the customer key, no current vehicle data is available, or the data does not match the maintenance schedule.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via the Voice over LTE (VoLTE) function. For this purpose, the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, BMW Assistance, and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via Voice over LTE (VoLTE) function. For this purpose the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, BMW Assistance and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The following complaints may be noticed while slow maneuvering with a steering input of 80-100% (at or near full lock, e.g., parking lot maneuvers) or accelerating with a medium to large steering angle: Humming or creaking noises from the rear area, slight vibrations also noticeable from the driver's seat. The vehicle may also jerk slightly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mist formation on the windshield inside surface may occur at departure or after MSA (automaticstart/stop). Acoustic abnormality in the area of the recirculated air flap (recirculation flap closing and opening severaltimes). The above may occur individually or in combination.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Check Control message "Door open" appears in the instrument cluster (Kombi) even though all vehicle doors are closed and locked. The locking operation of the doors is not affected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The quick disconnect coupling on the cylinder head coolant vent line could break at the cylinder head. This would lead to loss of coolant from the engine.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Any or all of the following CCM ID code 14/15/16/17 "door open" appear in the instrument cluster when the door is properly closed and locked. The locking operation of the door is not affected by the incorrect display.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Different air temperatures are felt from left to right out of the front fresh air grilles (air vent). The following fault code is saved in the IHKA (integrated automatic heating/air conditioning system) control unit: 801189 - Engine mixed air right: Initialization fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS UNIT DEACTIVATION DUE TO 3G CELLULAR TECHNOLOGY DISCONTINUATION: The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DOOR PAINT STREAKS: Streaks are found running mostly vertically down along the door outer skin from the lower window trim. This can affect any of the 4 side doors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Ingress In Footwell Area From A/C Condensate Drain: Water Ingress In Footwell Area From A/C Condensate Drain. Customer complains of musty odor or damp front footwell carpet.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full: Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONDENSATION FROM AIR CONDITIONING LEAKS INTO PASSENGER FOOTWELL: Condensation from the air conditioning systems evaporator drips, below the instrument panel, into the passenger's footwell. During assembly, the cover of the fresh air intake was not fully seated when the screws were tightened. This cover can then leak condensation out through the existing gap.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUZZING NOISE IS HEARD WHEN AIR CONDITIONING IS DEACTIVATED: A buzzing noise is heard when the air conditioning (A/C) is deactivated while the vehicle is in park or neutral. Prior to turning off the A/C, the system was functional and cooling properly. A/C compressor, or The power supply to the A/C compressor is too low.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONDENSATION FROM AIR CONDITIONING LEAKS INTO PASSENGER FOOTWELL: Condensation from the air conditioning systems evaporator drips, below the instrument panel, into the passenger's footwell. During assembly, the cover of the fresh air intake was not fully seated when the screws were tightened. This cover can then leak condensation out through the existing gap.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER · STRUCTURE:FRAME AND MEMBERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUZZING NOISE IS HEARD WHEN AIR CONDITIONING IS DEACTIVATED: A buzzing noise is heard when the air conditioning (A/C) is deactivated while the vehicle is in park or neutral. Prior to turning off the A/C, the system was functional and cooling properly. A/C compressor, or The power supply to the A/C compressor is too low.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ACTION - PROGRAM THE BODY DOMAIN CONTROL (BDC) UNIT: Aftermarket scan tools cannot read fault codes in the Dynamic Stability Control (DSC) unit via the On-Board Diagnostic (OBD) socket. The DSC data is not processed correctly in the BDC and therefore cannot transmit any diagnostic requests via the OBD using aftermarket scan tools.
Source components: ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DELIVERY STOP - OBD ACCESS IN DSC CONTROL UNIT: Aftermarket scan tools cannot read fault codes in the Dynamic Stability Control (DSC) unit via the On Board Diagnostic (OBD) socket. The DSC data is not processed correctly in the BDC and therefore cannot transmit any diagnostic requests via the OBD using aftermarket scan tools.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAILGATE MALFUNCTION WHEN OPENING OR CLOSING: Customer may complaint of any the following scenarios: When operating the tailgate by using any of the tailgate buttons, the movement stops Tailgate opens when the remote control is within the proximity of the rear of the vehicle, and a second person opens any of the doors using the outside door handle Tailgate opens again immediately after closing Erroneous ground signal set by the contactless tailgate opening control unit (smart-opener).
Source components: ELECTRICAL SYSTEM · EQUIPMENT · STRUCTURE:BODY:TAILGATE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NOISES FROM THE FUEL TANK AT IDLE: All vehicles except the F48 (X1): While driving slowly with low RPM or while idling a faint knocking or fluttering noise can be heard from inside the fuel tank with a low fuel level (approximately less than 2 gallons). The customer may describe this noise as a "helicopter noise" from the rear of the vehicle. F48 (X1) only: While driving slowly with low RPM or while idling a faint knocking or fluttering noise can be heard from inside the fuel tank when the tank is full. The customer may describe this noise as a "helicopter noise" from the rear of the vehicle. CAUSE Pressure fluctuations from the tank ventilation valve will cause the fuel tank filler pipe non-return valve to vibrate. In some cases, the vibration can be heard inside the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
F48 FUEL TANK VENT/PURGE VALVE LTD WARRANTY EXTENSION: This component-specific limited warranty extension applies to defects in materials or workmanship.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: A yellow CCM (Check Control Message) ID 415 is displayed- "Increased battery drain! // Battery. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation I01 only: FC 124103 - Mixture control: mixture too lean FC 124101 - Mixture control: Mixture lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ROUGH RUNNING IMMEDIATELY AFTER A COLD START: Immediately after a cold start the engine may run roughly during the catalyst heating period. Depending on the severity of this situation the malfunction indicator lamp (MIL) can be illuminated and the following fault code may be set: Fault code Control module Fault code text 151001 DME Ignition angle adjustment while idle speed cold start: ignition angle early In some circumstances if the vehicle is switched into a drive gear (R or D) when the RPM are low the engine may switch off. Should this occur the engine may be restarted normally. Software error in the DME.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAILGATE MALFUNCTION WHEN OPENING OR CLOSING: This Service Information Bulletin (Revision 1) replaces SI B61 06 20 dated February 2020. Customer may complaint of any the following scenarios: When operating the tailgate by using any of the tailgate buttons the movement stops Tailgate opens when the remote control is within the proximity of the rear of the vehicle and a second person opens any of the doors using the outside door handle Tailgate opens again immediately after closing Erroneous ground signal set by the contactless tailgate opening control unit (smart-opener).
NHTSA source summary · Original PDF not reviewed by Recallfolio
CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: This Service Information Bulletin (Revision 1) replaces SI B61 05 20 dated February 2020. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SAFETY BELT WARNING GONG SOUNDS AFTER UNBUCKLING WHILE VEHICLE IS STATIONARY. After a vehicle has been programmed to an I-level greater than 19-11-5xx and lower than I-level 20-03-530; the safety belt (aka seat belt) acoustic warning sounds when in Park (engine running) and the safety belt is unbuckled. The chime/gong lasts for up to 1 minute 40 seconds. The customer only expects the acoustic warning when the vehicle is moving and the safety belt is not buckled. The acoustic warning can occur when the seat is occupied and the safety belt buckle is opened on the driver's or passenger's side. Software in the ACSM4 Control Unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Ingress In Footwell Area From A/C Condensate Drain: This Service Information Bulletin (Revision 1) replaces SI B64 04 16 dated March 2016. The condensate drain hose is blocked by the heat shield The condensate drain hose is not attached properly to the housing The condensate drain hose was damaged during installation
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAILGATE MALFUNCTION WHEN OPENING OR CLOSING. Customer may complaint of any the following scenarios: When operating the tailgate by using any of the tailgate buttons the movement stops Tailgate opens when the remote control is within the proximity of the rear of the vehicle and a second person opens any of the doors using the outside door handle Tailgate opens again immediately after closing Erroneous ground signal set by the contactless tailgate opening control unit (smart-opener).
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES:TAILGATE:LATCH.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER. A yellow CCM (Check Control Message) ID 415 is displayed- "Increased battery drain! // Battery. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL LIGHT ILLUMINATED AT LOW AMBIENT TEMPERATURES. After engine start the malfunction indicator lamp (MIL) and Check Control message (ID 29) "Engine fault! Power loss" are displayed in the instrument cluster. In addition The following fault codes are stored in the Digital Motor Electronics (DME) Engine runs in failsafe mode Engine cannot exceed 800 - 1200 RPMs.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power-assisted Steering Intermittently Not Available at Engine Start-up: This Service Information Bulletin (Revision 1) replaces SI B32 02 14 dated November 2016. The power-assisted steering is unavailable at start up/drive readiness. No communication with the Electric Power Steering (EPS). Possible fault codes: Fault code Text D356A5 message fault (display of the check control driving dynamics 02 D: Disp_CC_DRDY_02) Timeout D359BF message fault (actual steering torque of the driver actuator ID: AVL_STMOM_DV_ACT) Timeout D356B6 message fault (display of the check control driving dynamics 02 ID: DISP_CC_DRDY_02) - Alive 480AB8 internal status management of the complete monitoring range CDA451 FlexRay message (actual steering torque of the driver actuator 49.0.2): missing CDA452 FlexRay message (actual force of the rack 49.0.2): missing D35B26 message fault (actual position of the EPS ID: AVL_PO_EPS) - Timeout D355C4 message fault (status of the electrical steering front axle ID: ST_EST) - Timeout 48083B Peripheral/functional error on the engine control unit interface Actual steering angle of the front axle; signal temporarily invalid D35COC message fault (actual force of the rack ID: AVL_FORC_GRD) - Timeout. Electric Power Steering (EPS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
DME FAULT CODE 1B8004 ENVIRONMENTAL AIR CATALYST(EAC) SENSOR: This Service Information Bulletin (Revision 1) replaces SI B13 02 18 dated April 2018. The Malfunction Indicator Lamp (MIL) light is on and the following fault code is stored in the DME: 1B8004 - EAC Sensor: Temperature - Engine coolant temperature radiator outlet comparison to each other implausible DME software calibration error for EAC sensor diagnostics.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MALFUNCTION INDICATOR LAMP IS ILLUMINATED WITH A CRANKSHAFT ADAPTION FAULT: When diagnosing an illuminated malfunction indicator lamp (MIL) and/or a different issue the following faults may also be stored in the Digital Motor Electronics (DME). Fault code Control module Fault code text 213A2B DME Increment wheel adaption faulty This situation is not associated with any drivability complaints and only affects vehicles built with a Factory I-level of 19-07-500 and later. An unfavorable DME diagnostic calibration may cause the fault code to be stored. In most circumstances this will cause the MIL to be illuminated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SIDE PANEL REAR LIGHT HOUSINGS: LTD WTY EXT TO 10 YEARS WITHOUT MILEAGE LIMIT: The rear light housing(s) can loosen/detach at the mounting tabs this can cause a clacking sound in the rear of the vehicle while driving. The plastic mounting tabs for the rear tail light assembly housing(s) may become too brittle and crack to the point where the hold down nut(s) can no longer keep the housing(s) in place.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NOISE DURING FORWARD / BACK SEAT ADJUSTMENT OVER THE ENTIRE LENGTH OF TRAVEL: A loud screeching noise can be heard from the front driver's or passenger's seat during forward/back seat adjustment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PHONE CONTACTS: HEADUNIT BASIC 2 SORTING ORDER: Improper sorting of phone contacts, in the on-board computer or in the Central Information Display (CID), upon connecting to the vehicle:
NHTSA source summary · Original PDF not reviewed by Recallfolio
DEACTIVATION OF CONTACTLESS TAILGATE OPENING AND CLOSING: Customer desires to have contactless tailgate opening and closing (Smart Opener) deactivated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUZZING NOISE FROM VALVETRONIC MOTOR BEFORE OR AFTER ENGINE OPERATION: Buzzing noise may be heard from the Valvetronic motor when the vehicle is unlocked, before the engine is started, or after the engine is turned off.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
COMPONENT PROTECTION ACTIVE. HEAD UNITS CANNOT BE SWAPPED BETWEEN VEHICLES FOR TESTING.: If either the head unit (NBT-EVO or ENTRY-NAV-EVO) or the Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head unit to enter a locked mode once it recognizes a different VIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION PRO (NBT EVO) MAP UPDATE NOT POSSIBLE, NAVIGATION DOES NOT START: Navigation system will not start at all or the: ÒNavigation system startsÓ message is permanently displayed; or
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHECK CONTROL STATES REMOTE KEY IS MISSING WHEN THE KEY IS LOCATED IN THE VEHICLE: Only affects vehicles that have been programmed with ISTA 4.10.1x and I-level 18-03-511 or 18-03-576
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INSTRUMENT CLUSTER OUTSIDE TEMPERATURE DISPLAY IMPLAUSIBLE: In the Instrument Cluster (Kombi) display you may observe an implausible outside temperature reading.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BASIC INSTRUMENT CLUSTER: DATE ERRONEOUSLY ADJUSTS BY ITSELF: The calendar date in the instrument cluster adjusts itself forward approximately one to two days.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VEHICLES WITH ENTRY NAVIGATION MAP 2017-2 ABORT PROGRAMMING: While installing the 2017-2 Europe and North America maps update with ISTA 4 software older than 4.08.3x, the installation aborts before finishing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION: Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONNECTEDDRIVE-REMOTE SERVICES DO NOT FUNCTION: Remote Services (such as locking and unlocking the car, vehicle location by honking the horn, flashing the lights or on the map in the BMW Connected App) do not function after vehicle has been sitting for extended amount of time (In excess of 20 hours).
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONTACTLESS TAILGATE (SMART OPENER) IS TOO SENSITIVE: When the remote is located in the range of the Smart Opener operation may be the contactless tailgate (Smart Opener) opens / close unintentionally from objects in the vicinity of the rear of the vehicle; for example by a gas filling hose.