2013 BMW X1 SAV Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–131 of 131, ordered newest first. Dated records on this page: Oct 1, 2012–Apr 1, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 1, 2014Service Bulletin/Repair Instructions
610314
NHTSA communication ID: 10148273
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Enabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: SERVICE ENGINE AND ENGINE MALFUNCTION LIGHT ILLUMINATES. VEHICLE MAY HAVE REDUCED POWER OUTPUT. FAULT CODE MAY NOT CLEAR FROM DME FAULT MEMORY. *KB UPDATED ON 11/8/2013. *KB UPDATED 2/21/2014 *JS UPDATED 3/11/14. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2013 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 It is good practice to verify that the part number being removed from the engine matches the new injector part number, until further notice. When the ETK data is corrected, a notification will be distributed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced up to 7/2013
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. Various faults related to VANOS operation are stored in the DME. While performing the test plan, the results may appear to be inconclusive because the fault will not clear from DME fault memory. CAUSE This is due to a programming error associated with ISTA/P 2.49 and lower. The error is corrected with ISTA/P 2.50.2 or higher.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Service Engine Soon Lamp On with Post Oxygen Sensor Faults Stored. The Service Engine Soon (MIL) lamp is on and the following faults are stored in the DME fault code memory. BN2000 (E-Series) vehicles: * 2D22: Oxygen sensor downstream of catalytic converter, electric: open circuit BN2020 (F-Series) vehicles: * 12AB04: Oxygen sensor downstream of catalytic converter, electric: open circuit * 12AC04: Oxygen sensor downstream of catalytic converter 2, electric: open circuit These faults may occur sporadically after a long MSA engine stop. Unfavorable DME software diagnostics (fault is erroneous) This software error affects vehicles produced from 3/2013 to 6/2013, as well as older vehicles which have been programmed during service work to a current integration level of Xxxx-13-03-5xx.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp is illuminated; Engine Malfunction warning is illuminated; and the vehicle has reduced power output. Various faults related to VANOS operation are stored in the DME. While performing the test plan, the results may appear to be inconclusive because the fault will not clear from DME Fault Memory. The ISTA/D diagnostic test plan does incorporate a VANOS bleed function, but it does not advise the technician to bleed the VANOS system after a VANOS or engine oil supply component replacement. CAUSE This is due to an error in the current level of ISTA/D. The error will be corrected with ISTA/D 2.41.0.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DSC Warning Light is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for 'Chassis Control System failure' One or more of the following fault codes are stored: F25, F30 DSC * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV"
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Engine Soon Light Flashes with Throttle Adaptation Faults Stored. The EML light flashes with a check control message for reduced power output and/or the Service Engine Soon lamp (MIL) flashes. During the throttle valve adaptation (teach-in limit run), faults may occur due to signal voltage oscillations. This could lead to a termination of the teach-in routine or an incorrect value taught in at the lower limit. The following faults can be stored in the DME memory: E82, E84, E88, E89, E92, and E93 BN2000 vehicles * 28D0: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 28D4: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 28C4: throttle valve, adaptation: Emergency air position not adapted * 28A0: throttle valve angle - Intake manifold absolute comparison: pressure too high ??3166: Tank-ventilation system: fault F01, F02, F06, F07, F10, F12, F13, F30, F31, and ALPINA B7 BN2020 vehicles: * 101408: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 107AE0: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 101402: throttle valve, adaptation: Emergency air position not adapted * 101F01: throttle valve angle - Intake manifold absolute comparison: pressure too high ??190F08: Tank-ventilation system: fault Sensitivity of the throttle valve sensor (only affects parts installed during this production period)
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: WARNING LAMPS ARE ILLUMINATED FOR THE DSC, ABS AND BRAKE AND A POSSIBLE WARNING IN CONTROL DISPLAY FOR CHASSIS CONTROL SYSTEM FAILURE. MODELS 2012 F25, 30, 01, 02, 07, 10, 12, 13, E70, 71, 84. *PE
Source components: EXTERIOR LIGHTING:BRAKE LIGHTS · SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT · SERVICE BRAKES, AIR:DISC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Driver's Door Mirror Adjustment Range Not Sufficient. The driver's door mirror inward travel is not sufficient. CAUSE The mirror glass carrier inward bump stop is too high and limits the inward travel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: BATTERY HAS AN INCREASED DEMAND DUE TO DEVELOPEMENTAL PROCESS OF THE ELECTRICAL SYSTEM. THIS IS CAUSING THE BATTER TO NEED TO UNDERGO AN ENERGY DIAGNOSIS. *KB
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Mirror Heating Not Working Properly. Mirror heating has no effect or works intermittently. CAUSE Door mirror software error This only affects E84 LCI models with option code: * 430 (Auto dimming door mirror) and /or * 459 (Electric seat adjustment with memory)
Source components: ELECTRICAL SYSTEM · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 Engine: Engine Oil Filter Application. INFORMATION The current version of EPC does not provide all available options for the engine oil filters that are used in the N20 engine. The illustrations below will help identify the proper engine oil filter application until the EPC is corrected. Vehicles produced prior to 6/2012 will be equipped with a black plastic oil filter housing (1). In this case, engine oil filter kit P/N 11 42 7 634 291 should be used. Vehicles produced as of 6/2012 and later will be equipped with a silver aluminum oil filter housing (1). In this case, engine oil filter kit P/N 11 42 7 640 862 should be used.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?N20 Engine: Repeated Juddering or Surging While Accelerating. The vehicle judders or surges repeatedly while accelerating in hot ambient temperatures between 3,000 RPM and 5,000 RPM. The Service Engine Soon lamp is not illuminated, and no fault codes are stored in the vehicle memory related to this complaint. CAUSE The EPDW (electropneumatic pressure convertor) for the turbocharger wastegate valve is binding internally.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Park Distance Control Does Not Work. When the reverse gear is selected or the PDC button is pressed, the rear PDC sensors do not work and, at times, there is no check control messages displayed. CAUSE Water ingresses into the PDC sensor. This is because the wire connection for the driver's side rear outer PDC sensor is not protected from water, dirt and other foreign materials kicked up by the driver's side rear wheel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Instrument Cluster Warning Displays Picture of Tailgate Open. The ""Tailgate open"" icon is displayed even though the tailgate is closed. The display icon may also illuminate when the engine is started. CAUSE The noise suppression filter for the aerial is faulty. Note: Replacing the JBE will not correct this issue."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."