The manufacturer’s record · Page 1 of 1
Original record summaries, dates and identifiers for this model-year. Records 1–23 of 23, ordered newest first. Dated records on this page: Oct 1, 2012–Jan 16, 2024.
Back to 2008 BMW 750LI problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10249437
NHTSA source summary · Original PDF not reviewed by Recallfolio
The basic conditions for initializing the power windows are not met.
Source components: ELECTRICAL SYSTEM · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
Source record 10249437 at NHTSANHTSA communication ID: 10249027
NHTSA source summary · Original PDF not reviewed by Recallfolio
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
Source components: ELECTRICAL SYSTEM.
Source record 10249027 at NHTSANHTSA communication ID: 10247567
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
Source record 10247567 at NHTSANHTSA communication ID: 10245422
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicleâÂÂs equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10245422 at NHTSANHTSA communication ID: 10225126
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10225126 at NHTSANHTSA communication ID: 10218398
NHTSA source summary · Original PDF not reviewed by Recallfolio
Component-Specific Limited Warranty Extension For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's front and rear air suspension strut assemblies (item # 1 Front and # 2 Rear, shown) to: 8 years/80,000 miles, as determined by the vehicle's original in-service date. Other air suspension system-related components/issues are excluded from this coverage. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.
Source components: ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · SUSPENSION.
Source record 10218398 at NHTSANHTSA communication ID: 10182619
NHTSA source summary · Original PDF not reviewed by Recallfolio
Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10182619 at NHTSANHTSA communication ID: 10145306
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10145306 at NHTSANHTSA communication ID: 10143564
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10143564 at NHTSANHTSA communication ID: 10146779
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: ELECTRICAL SYSTEM.
Source record 10146779 at NHTSANHTSA communication ID: 10151068
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: ELECTRICAL SYSTEM · ENGINE · EQUIPMENT · STEERING.
Source record 10151068 at NHTSANHTSA communication ID: 10147758
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B07 03 14 dated May 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: EQUIPMENT.
Source record 10147758 at NHTSANHTSA communication ID: 10147123
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: ELECTRICAL SYSTEM.
Source record 10147123 at NHTSANHTSA communication ID: 10147067
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: ELECTRICAL SYSTEM.
Source record 10147067 at NHTSANHTSA communication ID: 10147598
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SUBJECT N62TU: ISTA Service Function for DME ""RAM Backup"". The ISTA Service Function test plan should be performed to clear stored values in the DME RAM memory after repairs are completed, in the following situations: z VANOS or engine-related repairs if any of the following faults cannot be cleared: 2A90 - Exhaust camshaft, tooth offset to crankshaft 2A91 - Exhaust camshaft 2, tooth offset to crankshaft 2A8A - Inlet VANOS, adaptation stop 2A8B - Inlet VANOS, adaptation stop 2 2A8C - Exhaust VANOS, adaptation stop 2A8D - Exhaust VANOS, adaptation stop 2 2A8E - Inlet camshaft, tooth offset to crankshaft 2A8F - Inlet camshaft 2, tooth offset to crankshaft z The engine oil level display continues to show as overfilled even after being corrected. This is also described in SI B12 05 07."
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10147598 at NHTSANHTSA communication ID: 10148166
NHTSA source summary · Original PDF not reviewed by Recallfolio
N62TU: EDK Throttle Potentiometer Faults - Diagnostic. The "Service Engine Soon" and DSC/DTC warning lights are illuminated. Engine enters the power reduction ("fail-safe") mode. The following intermittent and "currently not present" EDK related faults may be stored in DME fault memory: ? 2CF8 - Throttle valve potentiometer, signal; and /or? 2CF9 - Throttle valve potentiometer 1, signal; and/or ? 2CFA - Throttle valve potentiometer 2; signal. In most cases DSC fault 5F77 (DME invalid data) may also be stored in DSC control module. These faults are sporadic and usually not reproducible. Resistance fluctuation in the EDK harness connector is causing an interruption of the EDK signal.
Source components: ELECTRICAL SYSTEM.
Source record 10148166 at NHTSANHTSA communication ID: 10149279
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: EQUIPMENT.
Source record 10149279 at NHTSANHTSA communication ID: 10057568
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: ON SOME VEHICLES, WHEN STARTING, LOW BEAM, WITH 0552 OPTION, WOULD BRIEFLY FLASHES, DUE TO A FAULTY LED MAIN LIGHT MODULE THAT NEEDS REPLACING. MODEL 2008-14 F01, F02, F06, F07, F10, F12, F13, F25. *PE
Source components: EXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH.
Source record 10057568 at NHTSANHTSA communication ID: 10148120
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
Source components: ELECTRICAL SYSTEM.
Source record 10148120 at NHTSANHTSA communication ID: 10148273
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10148273 at NHTSANHTSA communication ID: 10147945
NHTSA source summary · Original PDF not reviewed by Recallfolio
Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
Source components: EXTERIOR LIGHTING.
Source record 10147945 at NHTSANHTSA communication ID: 10152354
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Message Displayed; Turn Signals Flash Fast.
Source components: EXTERIOR LIGHTING:TURN SIGNAL.
Source record 10152354 at NHTSANHTSA communication ID: 10150330
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
Source components: ELECTRICAL SYSTEM.
Source record 10150330 at NHTSA