The manufacturer’s record · Page 1 of 1
Original record summaries, dates and identifiers for this model-year. Records 1–33 of 33, ordered newest first. Dated records on this page: Jan 1, 2006–Jan 16, 2024.
Back to 2005 BMW 325I problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10249437
NHTSA source summary · Original PDF not reviewed by Recallfolio
The basic conditions for initializing the power windows are not met.
Source components: ELECTRICAL SYSTEM · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
Source record 10249437 at NHTSANHTSA communication ID: 10249027
NHTSA source summary · Original PDF not reviewed by Recallfolio
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
Source components: ELECTRICAL SYSTEM.
Source record 10249027 at NHTSANHTSA communication ID: 10194296
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
Source components: SERVICE BRAKES, AIR:DISC · STEERING: STEERING WHEEL/HANDLE BAR.
Source record 10194296 at NHTSANHTSA communication ID: 10184591
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ACTION - HEAD AIR BAG HOLDER RETROFIT: A rattle noise may develop from the head air bag (ITS) gas generator contacting adjacent component. This noise can be heard while driving on an uneven roadway.
Source components: AIR BAGS:FRONTAL · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10184591 at NHTSANHTSA communication ID: 10182619
NHTSA source summary · Original PDF not reviewed by Recallfolio
Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10182619 at NHTSANHTSA communication ID: 10181217
NHTSA source summary · Original PDF not reviewed by Recallfolio
E46 SULEV/PZEV: FUEL TANK DISPOSAL PROCEDURE: E46 M56 vehicles, in addition to meeting the SULEV (Super Ultra Low Emission) tailpipe emission standard, also conform to the Zero Evaporative Emissions (PZEV) regulations. In order to meet these strict standards, the SULEV's fuel tank is a completely sealed unit manufactured from a high-grade stainless steel.
Source components: ENGINE AND ENGINE COOLING.
Source record 10181217 at NHTSANHTSA communication ID: 10160287
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
Source components: AIR BAGS.
Source record 10160287 at NHTSANHTSA communication ID: 10160244
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
Source components: AIR BAGS.
Source record 10160244 at NHTSANHTSA communication ID: 10153726
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAKATA CLASS ACTION SETTLEMENT. CUSTOMER SUPPORT PROGRAM. FRONT DRIVER SIDE AIRBAG MODULES.
Source components: AIR BAGS · AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE.
Source record 10153726 at NHTSANHTSA communication ID: 10149558
NHTSA source summary · Original PDF not reviewed by Recallfolio
For the above-referenced vehicles with passenger?s side airbag modules, BMW of North America, LLC (?BMW NA?) will provide a Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata passenger?s side airbag module in a listed vehicle.
Source components: AIR BAGS · ELECTRICAL SYSTEM.
Source record 10149558 at NHTSANHTSA communication ID: 10149557
NHTSA source summary · Original PDF not reviewed by Recallfolio
For the above-referenced vehicles with driver?s side airbag modules, BMW of North America, LLC (?BMW NA?) will provide a Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata driver?s side airbag module in a listed vehicle.
Source components: AIR BAGS · ELECTRICAL SYSTEM.
Source record 10149557 at NHTSANHTSA communication ID: 10145320
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: ConnectedDrive/BMW Assist features are partially or completely inoperative.
Source components: EQUIPMENT.
Source record 10145320 at NHTSANHTSA communication ID: 10145287
NHTSA source summary · Original PDF not reviewed by Recallfolio
E46 PZEV/SULEV (M56) FUEL TANKS: REPLACEMENT AND PARTS RETURN PROCEDURE: BMW of North America, LLC (ÒBMW NAÓ) will begin offering factory remanufactured fuel tank assemblies for E46 (3 Series) PZEV/SULEV (Model vehicles with the M56 engine).
Source components: FUEL SYSTEM, GASOLINE:STORAGE:AUXILLARY TANK.
Source record 10145287 at NHTSANHTSA communication ID: 10145306
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10145306 at NHTSANHTSA communication ID: 10143564
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10143564 at NHTSANHTSA communication ID: 10154816
NHTSA source summary · Original PDF not reviewed by Recallfolio
In an effort to improve the completion rate on Takata air bag recall affected vehicles; BMW NA has expanded the BMW Ultimate Rewards platform to include a new Recall Support page. This page will allow IRFs to check their customers VINs for open Takata recalls; and get rewarded for helping us with completing repairs.
Source components: AIR BAGS.
Source record 10154816 at NHTSANHTSA communication ID: 10142910
NHTSA source summary · Original PDF not reviewed by Recallfolio
FRONT PASSENGER SEAT OCCUPANCY (OC3) MAT FOR SRS: LIMITED WARRANTY EXTENSION TO 15 YEARS/UNLIMITED MILES
Source components: SEATS.
Source record 10142910 at NHTSANHTSA communication ID: 10147242
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
Source components: SERVICE BRAKES, HYDRAULIC · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC.
Source record 10147242 at NHTSANHTSA communication ID: 10147133
NHTSA source summary · Original PDF not reviewed by Recallfolio
"BMW NA is not requesting that these fuel tanks be returned to the Warranty Parts Return Center (WPRC) after a claim payment. When performing a fuel tank replacement on an E46 ""3 Series with the M56 SULEV (PZEV) engine"" (claim and non-claim related), the following pre-disposal procedure must be performed prior to scrapping the fuel tank. BEFORE STARTING AND WHILE CONDUCTING THE STEEL FUEL TANK DISPOSAL , FOLLOW ALL LOCAL AND STATE LAWS AND REGULATIONS PERTAINING TO HANDLING OF FLAMMABLE LIQUIDS. DO NOT USE ANY ELECTRICALLY POWERED TOOLS OR OPEN-FLAME DEVICES (E.G., ACETYLENE TORCHES) DURING THIS."
Source components: ENGINE · FUEL SYSTEM, GASOLINE.
Source record 10147133 at NHTSANHTSA communication ID: 10148179
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosis of Compound Brake System Complaints in M Vehicles. INFORMATION 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons. When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3. After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10148179 at NHTSANHTSA communication ID: 10148100
NHTSA source summary · Original PDF not reviewed by Recallfolio
Special Technical Campaign. The National Highway Traffic Safety Administration (NHTSA) has urged vehicle manufacturers to conduct an investigation into air bags which may not deploy correctly. BMW is cooperating with this request. Takata is a supplier of air bags to several automotive manufacturers. They have informed NHTSA of a small number of cases of improperly deploying air bags in a few specific areas of the US. None of the reported cases involve any BMW vehicles. No determination has been made by BMW and Takata that a safety issue exists.This program involves the driver and front passenger air bag system. Specifically, the air bag system may have been manufactured with an inflator that was not produced to specification. After long-term exposure in high absolute humidity environments, in a crash in which air bag system deployment occurs, the air bag system housing may rupture. To assist Takata with their determination, BMW will be collecting air bags from a limited number of customer vehicles. Once the affected vehicle population has been determined, owners of affected vehicles will be notified by letter to visit their authorized BMW center to have their air bag(s) replaced. Additional information will be provided at that time. A press release from NHTSA on this topic is expected to be issued on Monday, June 23, 2014.
Source components: AIR BAGS.
Source record 10148100 at NHTSANHTSA communication ID: 10147919
NHTSA source summary · Original PDF not reviewed by Recallfolio
As a safety precaution, when handling fuel tank always wear safety goggles and plastic (not latex) gloves, Nitrile preferred. 2.Remove defective fuel tank from the vehicle and place it on a workbench in an area where good ventilation is provided. As outlined in SI B01 03 14, starting in March 2014, the initial phase of the E46 SULEV (PZEV) fuel tank remanufacturing process will begin. When this fuel tank is replaced and a corresponding claim is submitted for reimbursement, BMW NA will request that the fuel tank be returned to the Warranty Parts Return Center (WPRC) after claim payment. Please ensure that your workshop technicians and Parts department personnel handle the removed fuel tank(s) properly to avoid unnecessary damage. The fuel tank disposal procedure outlined in the bulletin applies only to non-claim related tank replacements. BMW NA will not request that these tanks be returned to the WPRC. In the case of a non-claim related fuel tank replacement on an E46 3 Series M56 SULEV (PZEV) engine vehicle, the following disposal procedure must be performed prior to scrapping a non-returned requested fuel tank. BEFORE STARTING AND WHILE CONDUCTING THE STEEL FUEL TANK DISPOSAL , FOLLOW ALL LOCAL AND STATE LAWS AND REGULATIONS PERTAINING TO HANDLING OF FLAMMABLE LIQUIDS. DO NOT USE ANY ELECTRICALLY POWERED TOOLS OR OPEN-FLAME DEVICES (E.G., ACETYLENE TORCHES) DURING THIS
Source components: FUEL SYSTEM, GASOLINE.
Source record 10147919 at NHTSANHTSA communication ID: 10147916
NHTSA source summary · Original PDF not reviewed by Recallfolio
"E46 SULEV (PZEV) Fuel Tanks: New Warranty Parts Return Procedure. BMW of North America, LLC (""BMW NA"") will begin offering factory remanufactured fuel tank assemblies for E46 3 Series SULEV (Super Ultra Low Emission Vehicle)/PZEV (Partial Zero Emission Vehicle) model vehicles with the M56 engine. Starting in March 2014, the initial phase of the remanufacturing process will begin. When this fuel tank is replaced and a corresponding claim is submitted for reimbursement, BMW NA will request to have the fuel tank returned to the Warranty Parts Return Center (WPRC) after claim payment. Please ensure that your workshop technicians and Parts department personnel handle the removed fuel tank(s) properly to avoid unnecessary damage. The E46 SULEV (PZEV) Fuel Tank Disposal Procedure outlined in SI B16 01 04 applies only to non-claim related tank replacements. BMW NA will not request that these tanks be returned to the WPRC IMPORTANT INFORMATION A ""used"" fuel tank is eligible for classification as ""UN3363, Dangerous Goods in Apparatus, 9."" The following requirements apply when shipping: * There are limitations on the amount of liquid which can remain in the tank: It MUST be less than 0.5 liters of fuel. * The tank must be placed in strong outer packaging; this topic is addressed in the procedure section. * This package is a hazardous material shipment; you are required to mark the package accordingly, as noted in the procedure section. * As the shipper, your center is responsible for proper packaging and documentation completion. * The shipping document requires the UN number, proper shipping name and hazard class (UN3363, Dangerous goods in apparatus, 9), the number of packages and total quantity, along with a shipper's certification and a signature. * The person preparing and packaging the fuel tank(s) for shipping must have received the hazardous material training per 49CFR 172.702 and the IATA regulations. Those training records must be on file at your center. The U
Source components: FUEL SYSTEM, GASOLINE.
Source record 10147916 at NHTSANHTSA communication ID: 10150160
NHTSA source summary · Original PDF not reviewed by Recallfolio
State Inspection and Emission (I/M) Test Fails Due To an Invalid VIN Number. The customer of an affected vehicle may fail to pass an I/M test due to a non-compliant 17digit vehicle identification number (VIN) stored in the DME (Digital Motor Electronic). The VIN read out and displayed on the state test printout does not match the actual VIN of the vehicle. If the DME was reprogrammed using the previously available BMW service equipment (e.g., Progman, GT1), it is possible that only the last 7 digits of the VIN were entered into the DME, and positions 4 through10 may only contain default characters. For example: The state I/M tester or OBD scan tool may read out WBAAA00000A123456 instead of the correct full 17-digit VIN, WBAZZ03492A123456.
Source components: EQUIPMENT.
Source record 10150160 at NHTSANHTSA communication ID: 10150299
NHTSA source summary · Original PDF not reviewed by Recallfolio
E46 SULEV Fuel Tank Parts Collection . INFORMATION Starting on October 10th, 2013, BMW will be collecting defective E46 SULEV fuel tanks (P/N 16 11 6 763 569) for a special analysis project. To remove and prepare the fuel tank for shipping, please follow the procedure described below. Your dealer will receive a package addressed to your Shop Foreman, containing the plugs and caps needed to secure the fuel tank. If additional plug kits are needed, please contact Michael Murray via email at michael.murray@bmwna.com.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10150299 at NHTSANHTSA communication ID: 10037025
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: PROCEDURE FOR DETERMINING AND REPLACING INCANDESCENT AND HALOGEN LIGHT BULBS UNDER WARRANTY. *RM
Source components: EXTERIOR LIGHTING.
Source record 10037025 at NHTSANHTSA communication ID: 10036979
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: A NEW TECHNICAL PROCESS HAS BEEN CREATED FOR BMW TO IDENTIFY CAUSES OF STEERING COMPLAINTS WITH A WIDE RANGE OF MODELS. *RM
Source components: STEERING:ELECTRIC POWER ASSIST SYSTEM · STEERING:HYDRAULIC POWER ASSIST SYSTEM.
Source record 10036979 at NHTSANHTSA communication ID: 10033130
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW VEHICLES: FUEL LEVEL SENSOR REPAIRS. WHERE IT IS NECESSARY TO REPLACE THE RIGHT OR THE LEFT SIDE FUEL LEVEL SENSOR DUE TO A FAILURE, THE ENTIRE PUMP AND HOUSING OR DELIVERY UNIT (SUCTION JET ASSEMBLY) DO NOT NEED TO BE REPLACED AS WELL. IN SOME CASES, EPC DOES NOT SHOW THAT THE REPAIR KIT IS AVAILABLE SEPARATELY IN THE ILLUSTRATION, BUT IT IS AVAILABLE IN THE PARTS DESCRIPTION. ALL MODELS. NO MODEL YEARS LISTED. *PE
Source components: FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP.
Source record 10033130 at NHTSANHTSA communication ID: 10019998
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLUNTARY EMISSIONS RECALL 06E-A01: N52 - PROGRAMMING VEHICLE FOR OBD DIAGNOSTIC. MAY CAUSE THE OBD DIAGNOSTIC NOT TO DETECT POTENTIAL MALFUNCTIONS OF VARIOUS EMISSION RELEVANT SENSORS, CONSEQUENTLY, THE SERVICE ENGINE SOON LIGHT WILL NOT ILLUMINATE. *TT
Source components: ENGINE AND ENGINE COOLING:ENGINE.
Source record 10019998 at NHTSANHTSA communication ID: 10020254
NHTSA source summary · Original PDF not reviewed by Recallfolio
STEERING COLUMN CLICKING NOISE. *TT
Source components: STEERING:COLUMN.
Source record 10020254 at NHTSANHTSA communication ID: 10020005
NHTSA source summary · Original PDF not reviewed by Recallfolio
TOP TIER DETERGENT GASOLINE IN BMW VEHICLES. *TT
Source components: FUEL SYSTEM, GASOLINE.
Source record 10020005 at NHTSANHTSA communication ID: 10020004
NHTSA source summary · Original PDF not reviewed by Recallfolio
NITROGEN INFLATED TIRES. *TT
Source components: TIRES.
Source record 10020004 at NHTSANHTSA communication ID: 10012498
NHTSA source summary · Original PDF not reviewed by Recallfolio
AIRBAG WARNING LIGHT IS ILLUMINATED, AND FAULT CODE 71 (SEAT OCCUPANCY DETECTOR) IS STORED IN MRS4RD. BMW E83 (X3). MODEL YEAR UNKNOWN. *TT
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE.
Source record 10012498 at NHTSA