The vehicle dossier US · 2001
2001 Pontiac
GRAND AMProblems & recalls
538 distinct owner reports in the NHTSA snapshot. Electrical system appears in 232 of them. Explore what was reported—and which official actions are on file.
01 / Owner-reported evidence
What owners reported.
Categories attached to 538 distinct reports. A report can mention more than one component, so category totals can overlap.
See original component labels
These are reports made to NHTSA, not verified diagnoses. More reports can reflect more vehicles, more time on the road, or greater reporting activity.
The reporting timeline
When reports arrived.
Reports by year filed, not by the year a problem occurred. Showing the latest 15 years with reports.
71,000 miles is the median among 343 reports with usable mileage. The middle half spans 44,500–112,000 miles.
This describes the submitted reports. It does not predict when a vehicle will fail.
02 / Official safety campaigns
7 recall campaigns on file.
A campaign can cover only certain production dates or configurations. The count does not tell you whether an individual car has an open recall.
ELECTRICAL SYSTEM:IGNITIONCampaign 14V400000
Reported concern
This defect can affect the safe operation of the airbag system. Until this recall is performed, customers should remove all items from their key rings, leaving only the ignition key. The key fob (if applicable), should also be removed from the key ring. General Motors LLC (GM) notified the agency on July 3, 2014, that they are recalling 5,877,718 model year 2000-2005 Chevrolet Impala and Monte Carlo, 1997-2003 Chevrolet Malibu, 2004-2005 Malibu Classic, 1999-2004 Oldsmobile Alero, 1998-2002 Oldsmobile Intrigue, 1999-2005 Pontiac Grand Am and 2004-2008 Pontiac Grand Prix vehicles. In these models, the weight on the key ring and/or road conditions or some other jarring event may cause the ignition switch to move out of the run position, turning off the engine.
Manufacturer’s stated response
GM will notify owners, and dealers will install two key rings and an insert in the key slot or a cover over the key head on all ignition keys, free of charge. The recall began on September 9, 2014. GM's number for this recall is 14350.
Manufacturer campaign: 14350
Read campaign 14V400000 at NHTSAEXTERIOR LIGHTINGCampaign 09E012000
Reported concern
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.
Manufacturer’s stated response
SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.
Read campaign 09E012000 at NHTSAFUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY:PRESSURE RELIEF DEVICESCampaign 07E021000
Reported concern
CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.
Manufacturer’s stated response
DELPHI WILL NOTIFY OWNERS AND REPLACE THE UPR FREE OF CHARGE. THE RECALL BEGAN ON APRIL 23, 2007. OWNERS CAN CONTACT DELPHI AT 877-411-8770.
Read campaign 07E021000 at NHTSAEXTERIOR LIGHTINGCampaign 06E064000
Reported concern
CERTAIN TRADESONIC COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
Manufacturer’s stated response
TRADESONIC WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JULY 2006. OWNERS MAY CONTACT TRADESONIC AT 626-934-8884.
Read campaign 06E064000 at NHTSAEXTERIOR LIGHTING:HAZARD FLASHING WARNING LIGHTS:SWITCHCampaign 03V327000
Reported concern
CERTAIN PASSENGER VEHICLES HAVE HAZARD WARNING SWITCHES THAT MAY EXPERIENCE SOLDER JOINT CRACKING CAUSED BY RAPID TEMPERATURE TRANSITIONS AND THE SOLDERING PROCESS. IF SOLDER JOINT CRACKING OCCURS AND RESULTS IN AN OPEN CIRCUIT, THE TURN SIGNALS/HAZARD LAMPS BECOME INTERMITTENT OR INOPERATIVE.
Manufacturer’s stated response
DEALERS WILL REPLACE THE HAZARD WARNING SWITCH. OWNER NOTIFICATION BEGAN ON FEBRUARY 5, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438, PONTIAC AT 1-800-620-7668, OR OLDSMOBILE AT 1-800-630-6537.
Manufacturer campaign: 03043
Read campaign 03V327000 at NHTSAEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUALCampaign 03V250000
Reported concern
CERTAIN MINIVANS, PASSENGER AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEM." THE OWNER'S MANUAL DOES NOT EXPLAIN THE MEANING OF THE LOCATION SYMBOLS FOR THE CHILD RESTRAINT LOWER UNIVERSAL ANCHORAGE SYSTEM.
Manufacturer’s stated response
OWNERS WILL BE PROVIDED WITH A SUPPLEMENT FOR THEIR OWNER'S MANUAL. THIS SUPPLEMENT DESCRIBES AND SHOWS THE LOCATION SYMBOLS FOR THE CHILD RESTRAINT ANCHORS THAT ARE LOCATED IN THE VEHICLE AND ON THE CHILD RESTRAINT OR BOOSTER CUSHION. OWNER NOTIFICATION BEGAN AUGUST 18, 2003. OWNERS SHOULD CONTACT BUICK AT 1-866-608-8080, CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, GMC AT 1-866-996-9463, PONTIAC AT 1-800-620-7668, OR OLDSMOBILE AT 1-800-630-6537.
Manufacturer campaign: 03039
Read campaign 03V250000 at NHTSAPOWER TRAIN:MANUAL TRANSMISSIONCampaign 00V372000
Reported concern
VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES EQUIPPED WITH MANUAL TRANSAXLES (RPO M86) FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 114, "THEFT PROTECTION." WHEN A DRIVER ATTEMPTS TO SHIFT FROM 5TH GEAR TO REVERSE, A SHIFT INHIBITOR CAUSES THE TRANSMISSION TO BE MECHANICALLY IN 4TH GEAR EVEN THOUGH THE SHIFT LEVER INDICATES REVERSE GEAR.
Manufacturer’s stated response
DEALERS WILL DISABLE THE 5TH/REVERSE INHIBITOR BY REMOVING A RETAINING PIN AND REPLACE THE SHIFTER ASSEMBLY.
Manufacturer campaign: 00091
Read campaign 00V372000 at NHTSA03 / The manufacturer’s record
Instructions. Updates. Responses.
406 distinct communications list this model-year. Showing the latest 12. A matching model-year does not establish that every engine, trim or reported symptom is covered.
PIP5601CThis PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.NHTSA ID 11020816
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
Components: UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11020816 at NHTSAPIP5358DThis Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a …NHTSA ID 11014455
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
Components: UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11014455 at NHTSAPIP4723JThis Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/chargin…NHTSA ID 11009156
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.
Source record 11009156 at NHTSAPIT5099HThis Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will ne…NHTSA ID 11007744
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
Components: UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11007744 at NHTSAPIT5099HThis Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will ne…NHTSA ID 11007743
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
Components: UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11007743 at NHTSAGeneral CommunicationVehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updatin…NHTSA ID 11006621
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
Campaign / software reference: General Communication
Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.
Source record 11006621 at NHTSA18-NA-099This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.NHTSA ID 11004557
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
Components: UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11004557 at NHTSA24-NA-098This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution info…NHTSA ID 11002312
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.
Source record 11002312 at NHTSA16-NA-383This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Ti…NHTSA ID 10251890
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
Components: ENGINE AND ENGINE COOLING. Confirm detailed applicability in the original document.
Source record 10251890 at NHTSA22-NA-074This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.NHTSA ID 10250775
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
Components: ENGINE AND ENGINE COOLING. Confirm detailed applicability in the original document.
Source record 10250775 at NHTSAPIP5601BThis Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Os…NHTSA ID 10249980
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
Components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Confirm detailed applicability in the original document.
Source record 10249980 at NHTSAPI1394BThis PI bulletin advises the technician on the proper way to install the pistons in an engine.NHTSA ID 10249579
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
Components: ENGINE AND ENGINE COOLING · POWER TRAIN. Confirm detailed applicability in the original document.
Source record 10249579 at NHTSARecords below contain the NHTSA bulk summary unless a document-reviewed explainer is linked. A service bulletin is not a safety recall or a promise of a free repair. Records may be revised or superseded; verify the current document with the manufacturer.
04 / Agency investigations
Official inquiries.
An investigation is an inquiry into a potential concern. Its presence does not establish a defect, and a closed case does not certify a car’s condition.
TURN SIGNAL FAILURESEA02037
BY LETTER DATED AUGUST 27, 2003, GM NOTIFIED THE AGENCY THAT IT IS CONDUCTING A VOLUNTARY SAFETY RECALL (NHTSA RECALL NO. 03V327) INVOLVING CERTAIN MODEL YEAR (MY) 2000-2001 CHEVROLET MALIBU, OLDSMOBILE ALERO, AND PONTIAC GRAND AM.GM'S RECALL COVERS 670,740 VEHICLES MANUFACTURED BEGINNING FEBRUARY 1, 2000 THROUGH MAY 1, 2001 (ALERO AND GRAND AM) AND FEBRUARY 1, 2000 THROUGH MAY 31, 2001 (MALIBU).GM REPORTS THAT TURN SIGNAL FAILURE IS DUE TO SOLDER JOINT CRACKING IN THE HAZARD SWITCH, AND HAS IDENTIFIED RAPID TEMPERATURE TRANSITIONS OF THE HAZARD SWITCH AND THE SOLDERING PROCESS AS THE CAUSE OF CRACKING.ELECTRICAL CURRENT TO THE TURN SIGNALS FLOWS THROUGH THE HAZARD SWITCH AND AN OPEN CIRCUIT IN THE HAZARD SWITCH WILL CAUSE THE EXTERIOR TURN/HAZARD LAMPS TO BECOME INTERMITTENT OR INOPERATIVE.GM WILL REPLACE THE HAZARD SWITCH ON ALL INVOLVED VEHICLES.BASED ON GM'S SAFETY RECALL ACTION, THIS INVESTIGATION IS CLOSED.
Recorded closure: Sep 5, 2003
Campaign reference in the source: 03V327000
Find investigation EA02037ERRATIC FUEL GAUGEEA02028
ODI OPENED EA 02-028 TO REVIEW COMPLAINTS OF CONSUMERS REPORTING THAT THEIR FUEL GAUGE WAS INCORRECTLY DISPLAYING THE AMOUNT OF FUEL IN THE GAS TANK.THE FUEL GAUGE RECEIVES AN ELECTRICAL SIGNAL FROM A FUEL TANK SENDING SENSOR CIRCUIT CARD.A FLOAT ARM IN THE TANK MOVES ELECTRICAL CONTACTS THAT RUB AGAINST THE CARD AS THE LEVEL OF FUEL RISES AND FALLS.DISRUPTION OF THE ELECTRICAL SIGNAL (SUCH AS CAUSED BY CORROSION OF THE CIRCUIT CARD) WILL CAUSE INCORRECT READINGS TO REGISTER ON THE FUEL GAUGE.GM REPORTED IN THEIR RESPONSE TO ODI DATED JANUARY 13, 2003 THAT THE PRIMARY CAUSE OF ERRATIC FUEL GAUGE OPERATION IS EXCESS ELEMENTAL SULFUR IN FUEL.GM REPORTED THAT ABNORMAL LEVELS OF SULFUR SPORADICALLY OCCURRED IN CERTAIN PARTS OF CANADA AND THE U.S. RESULTING IN REPORTS OF FUEL GAUGE MALFUNCTION.GM MODIFIED THE SENDING SENSOR FOR VEHICLES BUILT AFTER OCTOBER 2000.IT MADE A SECOND SENSOR MODIFICATION FOR VEHICLES BUILT AFTER JANUARY 2003.GM ALSO ISSUED A CUSTOMER SATISFACTION CAMPAIGN (GM NUMBER 00101) IN DECEMBER 2000 FOR U.S. CUSTOMERS IN THE STATE OF MAINE AND ISSUED SEVERAL SERVICE BULLETINS INFORMING DEALERS OF THE AVAILABILITY OF SENSORS WITH IMPROVED CORROSION RESISTANCE.THE COMPLAINT TREND INDICATES THAT COMPLAINTS PEAKED IN LATE 2000 TO EARLY 2001.WARRANTY CLAIMS DECLINED SINCE PEAKING IN APRIL 2002.BASED ON THE NUMBER OF COMPLAINTS AND THE INDICATION OF A DECLINING TREND, FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.
Recorded closure: Dec 30, 2003
Find investigation EA02028ERRATIC FUEL GAUGESQ01002
Your next step
Take good questions
to the inspection.
Use these prompts with a qualified inspector. This page is research, not a diagnosis or a substitute for a hands-on inspection.