The vehicle dossier US · 2007
2007 Mercury
MOUNTAINEERProblems & recalls
81 distinct owner reports in the NHTSA snapshot. Other components appears in 44 of them. Explore what was reported—and which official actions are on file.
01 / Owner-reported evidence
What owners reported.
Categories attached to 81 distinct reports. A report can mention more than one component, so category totals can overlap.
See original component labels
These are reports made to NHTSA, not verified diagnoses. More reports can reflect more vehicles, more time on the road, or greater reporting activity.
The reporting timeline
When reports arrived.
Reports by year filed, not by the year a problem occurred. Showing the latest 15 years with reports.
75,000 miles is the median among 67 reports with usable mileage. The middle half spans 42,500–105,000 miles.
This describes the submitted reports. It does not predict when a vehicle will fail.
02 / Official safety campaigns
1 recall campaign on file.
A campaign can cover only certain production dates or configurations. The count does not tell you whether an individual car has an open recall.
VISIBILITY:GLASS, SIDE/REARCampaign 07E104000
Reported concern
CERTAIN CURVED TEMPERED REPLACEMENT GLASS MANUFACTURED BY HANGZHOU SAFETY GLASS LTD AND SUPPLIED TO SAFELITE BY AUTO TEMP INC., IDENTIFIED AS DOT-430, AND SOLD FOR USE ON CERTAIN DOMESTIC AND FOREIGN VEHICLES MAY NOT BREAK INTO SMALL PIECES AS EXPECTED OF TEMPERED GLASS AND FAILS TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 205, "GLAZING MATERIALS."
Manufacturer’s stated response
SAFELITE WILL NOTIFY ITS RETAIL CUSTOMERS AND REPLACE THE GLASS FREE OF CHARGE. RETAIL CUSTOMERS CAN CONTACT SAFELITE TOLL FREE AT 1-888-843-2906. SAFELITE WILL NOTIFY ITS WHOLESALE CUSTOMERS AND REIMBURSE WHOLESALE CUSTOMERS FOR CURRENT INVENTORY AND AT A SPECIFIED RATE FOR REPLACING THEIR CUSTOMER'S GLASS. WHOLESALE CUSTOMERS CAN CONTACT SAFELITE'S WHOLESALE DIVISION, SERVICE AUTOGLASS TOLL FREE AT 1-888-246-6298. THE RECALL BEGAN ON JANUARY 15, 2008.
Read campaign 07E104000 at NHTSA03 / The manufacturer’s record
Instructions. Updates. Responses.
22 distinct communications list this model-year. Showing the latest 12. A matching model-year does not establish that every engine, trim or reported symptom is covered.
SSM 51909When performing any transmission fluid changes or topoffs involving MERCON SP, MERCON LV has replaced all versions of MERCON SP and can be used going forward. Mixing MERCON LV and MERCON SP in the same transmission is acceptabl…NHTSA ID 10243490
When performing any transmission fluid changes or topoffs involving MERCON SP, MERCON LV has replaced all versions of MERCON SP and can be used going forward. Mixing MERCON LV and MERCON SP in the same transmission is acceptable. After 30-Jun-2023, MERCON SP ATF will no longer be manufactured and will only be available until inventory depletes.
Components: POWER TRAIN:AUTOMATIC TRANSMISSION. Confirm detailed applicability in the original document.
Source record 10243490 at NHTSATSB 19-2026Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is re…NHTSA ID 10156863
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
Components: EQUIPMENT · STRUCTURE. Confirm detailed applicability in the original document.
Source record 10156863 at NHTSATSB 19-2026Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is re…NHTSA ID 10155551
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
Components: STRUCTURE. Confirm detailed applicability in the original document.
Source record 10155551 at NHTSADOR-S3J9G-11This SKU is a front upper ball joint. The Customer communication requested return of unsold inventory to inspect for ball studs with excessive rotational friction in the ball joint assembly. Excessive friction in the ball joint…NHTSA ID 10148819
This SKU is a front upper ball joint. The Customer communication requested return of unsold inventory to inspect for ball studs with excessive rotational friction in the ball joint assembly. Excessive friction in the ball joint assembly may cause a perceptible increase in steering effort.
Components: STEERING. Confirm detailed applicability in the original document.
Source record 10148819 at NHTSASSM 47331Various vehicles equipped with a 4.6L, 5.4L, 6.8L modular 3 valve engine built on or before 8-Jan-2016 may exhibit symptoms that may include upper end engine noise, rough running, misfire and/or engine damage. If diagnosis lead…NHTSA ID 10143079
Various vehicles equipped with a 4.6L, 5.4L, 6.8L modular 3 valve engine built on or before 8-Jan-2016 may exhibit symptoms that may include upper end engine noise, rough running, misfire and/or engine damage. If diagnosis leads to only camshaft/camshaft roller follower(s) requiring replacement, replace all of the camshaft roller followers on both banks/cylinder heads with part number 3L3Z-6564-A, not just the faulty roller follower(s). When replacing the camshaft roller followers, refer to Workshop Manual (WSM), Section 303-01.
Components: ENGINE · EQUIPMENT. Confirm detailed applicability in the original document.
Source record 10143079 at NHTSASSM 46085The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited …NHTSA ID 10109070
The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
Components: ENGINE · ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN · ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS · ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY · ENGINE AND ENGINE COOLING:ENGINE · ENGINE AND ENGINE COOLING:ENGINE:DIESEL · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV) · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. Confirm detailed applicability in the original document.
Source record 10109070 at NHTSAASI-44429FORD/MERCURY: TO PREVENT HARNESS DAMAGE, ON SOME VEHICLES, RESULTING IN CONTACT WITH TIRE OR SUSPENSION COMPONENTS, PROPER ROUTING OF WIRING HARNESS FOR WHEEL SPEED SENSOR IS KEY. 2006-2010 EXPLORER, MOUNTAINEER, EXPLORER SPORT…NHTSA ID 10055318
FORD/MERCURY: TO PREVENT HARNESS DAMAGE, ON SOME VEHICLES, RESULTING IN CONTACT WITH TIRE OR SUSPENSION COMPONENTS, PROPER ROUTING OF WIRING HARNESS FOR WHEEL SPEED SENSOR IS KEY. 2006-2010 EXPLORER, MOUNTAINEER, EXPLORER SPORT TRAC. *PE
Components: ELECTRICAL SYSTEM:WIRING · SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING. Confirm detailed applicability in the original document.
Source record 10055318 at NHTSATSB-12-7-4FORD/LINCOLN/MERCURY: IF BATTERY WAS DISCONNECTED OR DEAD, VEHICLES/TRUCKS MAY EXPERIENCE HARD STARTS AND ENGINE IDLE RPM FLUCTUATION AND EXHIBIT DIAGNOSTIC TROUBLE CODES (DTCS) P0505, P0506, P2111 AND P2112. *PENHTSA ID 10045340
FORD/LINCOLN/MERCURY: IF BATTERY WAS DISCONNECTED OR DEAD, VEHICLES/TRUCKS MAY EXPERIENCE HARD STARTS AND ENGINE IDLE RPM FLUCTUATION AND EXHIBIT DIAGNOSTIC TROUBLE CODES (DTCS) P0505, P0506, P2111 AND P2112. *PE
Components: ENGINE. Confirm detailed applicability in the original document.
Source record 10045340 at NHTSATSB-08-18-2FORD/MERCURY/LINCOLN: VEHICLES MAY EXHIBIT ONE OR MORE OF THE FOLLOWING SYMPTOMS: DRIVE AWAY HESITATION, LOSS OF RPM ON DECELERATION, DIFFICULTY STARTING, AND/OR IDLE RPM LESS THAN DESIRED. THE F53 MOTORHOME CHASSIS IS INCLUDED…NHTSA ID 10029205
FORD/MERCURY/LINCOLN: VEHICLES MAY EXHIBIT ONE OR MORE OF THE FOLLOWING SYMPTOMS: DRIVE AWAY HESITATION, LOSS OF RPM ON DECELERATION, DIFFICULTY STARTING, AND/OR IDLE RPM LESS THAN DESIRED. THE F53 MOTORHOME CHASSIS IS INCLUDED. *PE
Components: ENGINE AND ENGINE COOLING:ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Confirm detailed applicability in the original document.
Source record 10029205 at NHTSATSB-08-19-3FORD: SOME VEHICLES MAY EXHIBIT OIL SEPARATION FROM THE INTERNAL LUBE FOUND IN THE UNITIZED CARTRIDGE SEAL. OIL SEPARATION APPEARS TO BE AND IS OFTEN MISDIAGNOSED, AS AN AXLE LUBE LEAK. *PENHTSA ID 10028736
FORD: SOME VEHICLES MAY EXHIBIT OIL SEPARATION FROM THE INTERNAL LUBE FOUND IN THE UNITIZED CARTRIDGE SEAL. OIL SEPARATION APPEARS TO BE AND IS OFTEN MISDIAGNOSED, AS AN AXLE LUBE LEAK. *PE
Components: POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT · POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT:SEAL. Confirm detailed applicability in the original document.
Source record 10028736 at NHTSATSB-08-9-5FORD/MERCURY: 4.0L/4.6L HARD START/ROUGH RUNNING; AFTER LONG HOT SOAK/DIP IN RPM WHEN COMING TO A STOP; BUILT ON OR BEFORE 4/2/08. MAY EXHIBIT A DIP IN RPM BELOW NORMAL IDLE LEVEL OF 600 RPM ON DECELERATION. *PENHTSA ID 10026385
FORD/MERCURY: 4.0L/4.6L HARD START/ROUGH RUNNING; AFTER LONG HOT SOAK/DIP IN RPM WHEN COMING TO A STOP; BUILT ON OR BEFORE 4/2/08. MAY EXHIBIT A DIP IN RPM BELOW NORMAL IDLE LEVEL OF 600 RPM ON DECELERATION. *PE
Components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Confirm detailed applicability in the original document.
Source record 10026385 at NHTSA20144MULTIPLE VEHICLE LINES - INTERMITTENT PCM, FUEL PUMP, IGN. COIL, A/C, ABS OR FOG LAMP OPERATION. *NJNHTSA ID 10024695
MULTIPLE VEHICLE LINES - INTERMITTENT PCM, FUEL PUMP, IGN. COIL, A/C, ABS OR FOG LAMP OPERATION. *NJ
Components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Confirm detailed applicability in the original document.
Source record 10024695 at NHTSARecords below contain the NHTSA bulk summary unless a document-reviewed explainer is linked. A service bulletin is not a safety recall or a promise of a free repair. Records may be revised or superseded; verify the current document with the manufacturer.
04 / Agency investigations
Official inquiries.
An investigation is an inquiry into a potential concern. Its presence does not establish a defect, and a closed case does not certify a car’s condition.
TIRE VALVE CRACKINGPE08060
ON OCTOBER 14, 2008, ODI OPENED PE08-060 TO INVESTIGATE ALLEGATIONS OF CRACKED AND LEAKING SNAP-IN TIRE VALVES IN MODEL YEAR (MY) 2007 VEHICLES MANUFACTURED BY FORD MOTOR COMPANY.THE VALVES WERE SUPPLIED TO FORD BY TOPSEAL AUTO-PARTS, A SUBSIDIARY OF THE SHANGHAI BAOLONG AUTOMOTIVE CORPORATION IN CHINA.VALVES MADE BY TOPSEAL FOR AFTERMARKET SALE WERE THE SUBJECT OF TWO RECENT SAFETY RECALLS BY TECH INTERNATIONAL (08T-018) AND DILL AIR CONTROLS (08T-028), THE LATTER OF WHICH WAS INVESTIGATED BY ODI IN PE08-036 AND EA08-022.THE DEFECT CONDITIONS ADDRESSED BY THE AFTERMARKET TIRE VALVE RECALLS BOTH INVOLVED INADEQUATE RESISTANCE TO OZONE CRACKING DUE TO ISSUES WITH THE SUPPLY OF ANTI-OZONANT CHEMICALS TO TOPSEAL FOR A PERIOD FROM JULY TO MID-NOVEMBER 2006.THE AFTERMARKET VALVES WERE COMPOUNDED WITH A BLEND OF EPDM AND NATURAL RUBBER, USING A RELATIVELY LOW PERCENTAGE OF EPDM (EPDM PROVIDES INHERENT RESISTANCE TO OZONE CRACKING).HENCE, THE NEED FOR ANTI-OZONANT CHEMICALS AND THE PROBLEMS WITH CRACKING WHEN THOSE CHEMICALS WERE MISSING OR OUT OF SPECIFICATION IN SOME LOTS OF VALVES.BOTH RECALL CAMPAIGNS INVOLVED INSPECTION PROGRAMS TO IDENTIFY AND REPLACE VALVES WITH VISIBLE SURFACE CRACKING.ALTHOUGH THE TOPSEAL VALVES SUPPLIED TO FORD ALSO APPEAR TO HAVE BEEN AFFECTED BY THE ANTI-OZONANT SUPPLY ISSUES IN MID TO LATE-2006, FORD INDICATED THAT ITS VALVES WERE MADE AT A DIFFERENT TOPSEAL PRODUCTION LINE AND WERE COMPOUNDED WITH A HIGHER PERCENTAGE OF EPDM RUBBER TO MEET MORE STRINGENT SPECIFICATIONS FROM FORD.ODI'S ANALYSIS OF COMPLAINT AND WARRANTY DATA PROVIDED BY FORD SHOWED THAT PROBLEMS WITH CRACKED TIRE VALVES WERE SIGNIFICANTLY HIGHER FOR MY 2007 VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007.FORD RESPONDED BY IMPLEMENTING CHANGES IN ITS MATERIAL SPECIFICATIONS FOR SNAP-IN RUBBER TIRE VALVES AND ALSO INCREASING THE QUALITY AND ACCEPTANCE STANDARDS FOR VALVES IMPORTED FOR USE IN ITS VEHICLES.WHILE THE COMPLAINT AND WARRANTY CLAIM RATES ARE ELEVATED FOR SUBJECT VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007, THE RATES OF LEAKING VALVES ARE WELL BELOW ONE PERCENT OF PRODUCTION FOR EACH OF THE PEAK MONTHS FOR ALL OF THE AFFECTED MODELS.A SUBSTANTIAL MAJORITY OF THE SUBJECT VEHICLES ARE EQUIPPED WITH TIRE PRESSURE MONITORING SYSTEMS (TPMS) WHICH WARN THE DRIVER WHEN ANY TIRE PRESSURES DROPS BELOW 25 PERCENT OF RECOMMENDED INFLATION PRESSURE. AS OUTLINED IN A LETTER TO ODI DATED APRIL 6, 2009, FORD HAS AGREED TO SEND LETTERS TO OWNERS OF CERTAIN MY 2007 AND 2008 FORD, LINCOLN AND MERCURY VEHICLES TO PROVIDE INFORMATION ABOUT THE CRACKING CONCERN. LETTERS WILL BE SENT TO OWNERS OF VEHICLES BUILT FROM NOVEMBER 2006 THROUGH MAY 2007.OWNERS CAN OPT FOR A FREE DEALER INSPECTION.VALVES EXHIBITING SURFACE CRACKS OR AIR LEAKAGE RELATED TO OZONE ATTACK WILL BE REPLACED BY FORD UNDER ITS NORMAL WARRANTY TERMS.FORD EXPECTS TO SEND THE LETTER BY APPROXIMATELY MID-MAY 2009. BASED ON THE USE OF TPMS IN THE MAJORITY OF SUBJECT VEHICLES AND THE RELATIVELY LOW RATES OF REPAIRS ASSOCIATED WITH LEAKING VALVES AND RESULTANT TIRE DAMAGE, ODI BELIEVES THAT THE ACTIONS FORD HAS AGREED TO TAKE WILL PROVIDE EFFECTIVE AND EXPEDITIOUS RESOLUTION FOR VEHICLES THAT WERE BUILT DURING THE PERIOD WHEN VALVES WITH INADEQUATE RESISTANCE TO OZONE CRACKING WERE MOST LIKELY TO HAVE BEEN USED IN VEHICLE PRODUCTION.FURTHER INVESTIGATION OF THIS MATTER WOULD NOT BE AN EFFICIENT ALLOCATION OF AGENCY RESOURCES.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO
Recorded closure: Apr 9, 2009
Find investigation PE08060Your next step
Take good questions
to the inspection.
Use these prompts with a qualified inspector. This page is research, not a diagnosis or a substitute for a hands-on inspection.