2012 Mercedes-Benz
ML350Problems & recalls

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Components: STEERING. Confirm detailed applicability in the original document.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Components: POWER TRAIN. Confirm detailed applicability in the original document.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Components: SUSPENSION. Confirm detailed applicability in the original document.

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Components: SUSPENSION. Confirm detailed applicability in the original document.

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Components: EXTERIOR LIGHTING. Confirm detailed applicability in the original document.

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Components: EXTERIOR LIGHTING. Confirm detailed applicability in the original document.

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Components: EXTERIOR LIGHTING. Confirm detailed applicability in the original document.

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Components: EXTERIOR LIGHTING. Confirm detailed applicability in the original document.

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. **NOTE - As of Sept 2025 the pressure testing tool is not finalized and may require modifications to fit properly. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

Components: EXTERIOR LIGHTING. Confirm detailed applicability in the original document.

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).

Components: POWER TRAIN. Confirm detailed applicability in the original document.