2013 Lincoln
MKXProblems & recalls

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

Components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.

Certain 2010-2014 Model Year Edge and MKX Vehicles - Extended Warranty Coverage on Brake Booster

Components: SERVICE BRAKES, HYDRAULIC. Confirm detailed applicability in the original document.

Certain 2010-2014 Model Year Edge and MKX Vehicles - Extended Warranty Coverage on Brake Booster

Components: SERVICE BRAKES, HYDRAULIC. Confirm detailed applicability in the original document.

For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

Components: STRUCTURE. Confirm detailed applicability in the original document.

These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

Components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. Confirm detailed applicability in the original document.

These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

Components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. Confirm detailed applicability in the original document.

Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.

Customer Satisfaction Program 19N09 Certain 2011-2014 Model Year Edge and MKX and 2013-2014 Model Year Explorer, Flex, and MKT Vehicles Left Front Door Latch Extended Coverage

Components: LATCHES/LOCKS/LINKAGES · STRUCTURE. Confirm detailed applicability in the original document.

Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

Components: VISIBILITY · VISIBILITY:GLASS, SIDE/REAR. Confirm detailed applicability in the original document.

For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.

On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

Components: POWER TRAIN. Confirm detailed applicability in the original document.

SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

Components: ENGINE. Confirm detailed applicability in the original document.