2000 Ford
FOCUSProblems & recalls

Reported concern

RIDE CONTROL, LLC (RIDE CONTROL) IS RECALLING CERTAIN READYMOUNT ASSEMBLIES, P/N 746641MT AND 746646MT, WITH CORRESPONDING AFTERMARKET CUSTOMER PART NUMBERS: GABRIEL G56944 AND GABRIEL G56945, AND PRIVATELY BRANDED PARTSMASTER WITH PART NUMBERS G68944 AND G68945. THE READYMOUNT ASSEMBLIES WERE SOLD AS AFTERMARKET SERVICE EQUIPMENT FOR USE ON CERTAIN 2000 THROUGH 2005 FORD FOCUS VEHICLES. THESE ASSEMBLIES WERE ASSEMBLED WITH A NUT WITHOUT THE NECESSARY WASHER. THE ABSENCE OF THE WASHER CAN ALLOW THE READYMOUNT ASSEMBLY TO PULL APART THE TOP MOUNT.

Manufacturer’s stated response

RIDE CONTROL WILL NOTIFY OWNERS AND WILL SET UP PROCEDURES TO INSPECT, REPAIR, AND/OR REPLACE THE AFFECTED PARTS WITHOUT CHARGE TO THE OWNER. THE SAFETY RECALL BEGAN ON MARCH 30, 2012. OWNERS MAY CONTACT RIDE CONTROL AT 1-800-999-3903.

Reported concern

DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Manufacturer’s stated response

DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.

Reported concern

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Manufacturer’s stated response

SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

Reported concern

K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

Manufacturer’s stated response

K2 MOTOR WILL NOTIFY OWNERS AND OFFER A FULL REFUND. THE RECALL BEGAN ON DECEMEBER 17, 2008. OWNERS MAY CONTACT K2 MOTOR AT 1-909-839-2992.

Reported concern

CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Manufacturer’s stated response

CK MOTORSPORT WILL NOTIFY OWNERS AND REPLACE THE NONCOMPLIANT LAMPS FREE OF CHARGE. THE RECALL BEGAN ON JULY 1, 2006. OWNERS MAY CONTACT CK MOTORSPORT AT 1-909-610-7211.

Reported concern

CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Manufacturer’s stated response

PRO-A MOTORS WILL NOTIFY OWNERS AND OFFER TO REPURCHASE THE LAMPS. THE RECALL BEGAN ON APRIL 3, 2006. OWNERS MAY CONTACT PRO-A MOTORS AT 323-838-2988.

Reported concern

CERTAIN PASSENGER VEHICLES WITH FOUR OR FIVE DOORS AND ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA, A BUILD-UP OF CORROSION AT THE PAWL PIVOT AREA OF THE REAR DOOR LATCH CAN CAUSE A BINDING CONDITION OF THE PAWL THAT MAY AFFECT PROPER ENGAGEMENT OF THE PAWL INTO THE CATCH. THE OCCUPANT MAY EXPERIENCE DIFFICULTY OPENING OR CLOSING A REAR DOOR, AND EVENTUALLY THE REAR DOOR MAY NOT LATCH PROPERLY.

Manufacturer’s stated response

DEALERS WILL HAVE A LOWER ROCKER SEAL ADDED TO THE DOOR AND HAVE THE REAR DOOR LATCHES EVALUATED FREE OF CHARGE. A LATCH THAT PASSES THE EVALUATION WILL BE LUBRICATED TO PREVENT FUTURE CORROSION. A LATCH THAT DOES NOT PASS THE EVALUATION WILL BE REPLACED. IN ADDITION, A STICKER WILL BE AFFIXED TO THE REAR DOORS ADVISING THE OWNERS TO USE THE RECOMMENDED LUBRICANT. THE RECALL BEGAN ON MARCH 9, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673.

Manufacturer campaign: 05S27

Reported concern

ON CERTAIN PASSENGER VEHICLES, CONTAMINATION OF THE FILTER IN THE FUEL DELIVERY MODULE (FDM) CAN REDUCE, AND EVENTUALLY BLOCK, THE FLOW OF FUEL TO THE ENGINE.

Manufacturer’s stated response

THIS ACTION IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN AND IS NOT BEING CONDUCTED UNDER THE SAFETY ACT. ALL OWNERS WILL BE NOTIFIED OF THE PROBLEM, AND DEALERS WILL REPLACE THE FDM WITH A NEW DESIGN AT NO CHARGE IF THE OWNER REPORTS THAT THE VEHICLE EXHIBITS ANY OF THE IDENTIFIED SYMPTOMS. THE FREE REPLACEMENT WILL BE AVAILABLE FOR A PERIOD OF 10 YEARS FOLLOWING THE ORIGINAL PURCHASE OF THE VEHICLE, WITH NO MILEAGE LIMIT. OWNER NOTIFICATION IS EXPECTED TO BEGIN DURING NOVEMBER 2003. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.

Manufacturer campaign: 03N01

Reported concern

CERTAIN PASSENGER VEHICLES HAVE LOOSE PINCH BOLTS THAT SECURE THE LOWER CONTROL ARM TO THE STEERING KNUCKLE HAVE BEEN REPORTED.

Manufacturer’s stated response

DEALERS WILL INSPECT THE STEERING KNUCKLE PINCH BOLT FOR TIGHTNESS AND CORRECT AS NECESSARY. OWNER NOTIFICATION BEGAN FEBRUARY 10, 2003. OWNERS WHO DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

Manufacturer campaign: 02S42

Reported concern

CERTAIN PASSENGER VEHICLES EQUIPPED WITH ZETEC ENGINES, LOOSE OR BROKEN ATTACHMENTS AND MISROUTED BATTERY CABLES COULD LEAD TO CABLE INSULATION DAMAGE.

Manufacturer’s stated response

DEALERS WILL INSPECT THE BATTERY CABLES FOR THE CONDITION OF THE CABLE INSULATION AND PROPER TIGHTENING OF THE TERMINAL ENDS. AS NECESSARY, CABLES WILL BE REROUTED, RETAINING CLIPS INSTALLED, AND DAMAGED BATTERY CABLES REPLACED. OWNER NOTIFICATION BEGAN FEBRUARY 10, 2003. OWNERS WHO DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

Manufacturer campaign: 02S41

Reported concern

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 2000-2001 FORD FOCUS PASSENGER VEHICLES, ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIOM, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN. IN HIGH CORROSION AREAS, WHERE SALT IS USED ON ROADWAYS IN THE WINTER, THE REAR WHEEL BEARING SEAL RACE CAN EXPERIENCE SURFACE CORROSION. IF THIS CONDITION OCCURS, THE WHEEL BEARING SEALS COULD BECOME DAMAGED AND ALLOW CONTAMINATION TO ENTER THE WHEEL BEARINGS.

Manufacturer’s stated response

DEALERS WILL REPLACE THE REAR WHEEL BEARINGS AT NO COST TO THE CONSUMER. ADDITIONAL BEARING SEALS WILL ALSO BE INSTALLED TO ENSURE A SMOOTH RIDE. THIS PROGRAM WILL BE IN EFFECT UNTIL DECEMBER 31, 2002, REGARDLESS OF MILEAGE. EVEN IF THE VEHICLE HAS ALREADY BEEN SERVICED UNDER RECALL CAMPAIGN 00S31, FORD HAS TAKEN ADDITIONAL STEPS TO KEEP THE WHEEL BEARINGS IN TOP SHAPE. OWNERS CAN CONTACT FORD AT 1-866-436-7332, CONCERNING THIS PROGRAM.

Reported concern

VEHICLE DESCRIPTION: PASSENGER CARS, SPORT UTILITY VEHICLES, AND LIGHT AND MEDIUM DUTY PICKUP TRUCKS. A SWITCH LOCATED IN THE PLASTIC COVER OF THE WIPER MOTOR GEAR CASE COULD MALFUNCTION AND OVERHEAT, POTENTIALLY RESULTING IN LOSS OF INTERMITTENT WIPER FUNCTION, LOSS OF WIPER PARK FUNCTION, COMPLETE LOSS OF WIPER FUNCTION, OR IGNITION OF THE PLASTIC COVER MATERIAL. SWITCH MALFUNCTION IS MOST LIKELY TO OCCUR WHEN THE INTERMITTENT SETTING OF THE WIPERS IS BEING USED, OR WHEN SNOW OR ICE OBSTRUCTS THE BLADES FROM RETURNING TO THE "PARKED" POSITION AT THE BOTTOM OF THE WINDSHIELD. THESE VEHICLES WERE BUILT AT THE FOLLOWING ASSEMBLY PLANTS: ATLANTA PLANT FROM 2/11/00 THROUGH 7/31/00; CHICAGO PLANT FROM 2/14/00 THROUGH 8/4/00; KANSAS CITY PLANT FROM 2/26/00 TO 9/4/00; KENTUCKY TRUCK PLANT FROM 2/18/00 TO 8/31/00; MICHIGAN TRUCK PLANT FROM 2/23/00 THROUGH 8/3/00; NORFOLK PLANT FROM 2/21/00 THROUGH 7/27/00; WAYNE STAMPING AND ASSEMBLY PLANT FROM 2/25/00 THROUGH 8/15/00; AND WIXOM PLANT FROM 2/15/00 THROUGH 8/8/00.

Manufacturer’s stated response

DEALERS WILL INSPECT THE DATE CODE ON THE WIPER MOTOR. MOTORS BUILT WITH THE SUSPECT TIME FRAME WILL HAVE THE WIPER MOTOR GEAR CASE COVER REPLACED. OWNER NOTIFICATION BEGAN AUGUST 20, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

Manufacturer campaign: 01S24

Reported concern

VEHICLE DESCRIPTION: STATION WAGONS AND 3-DOOR VEHICLES. THE SUBJECT VEHICLES HAVE A FOLDING 60/40 SECOND SEAT THAT BECOMES A LOAD FLOOR IN THE FOLDED POSITION. WHEN THE 60% PORTION OF THE SEAT IS FOLDED DOWN AND A LOAD IS APPLIED TO THE FRONT EDGE OF THE LOAD FLOOR, THE OUTBOARD HINGE PIVOT COULD DISENGAGE FROM THE HINGE.

Manufacturer’s stated response

DEALERS WILL INSTALL A REVISED SEAT BACK HINGE PIVOT.

Manufacturer campaign: 00S55

Reported concern

VEHICLE DESCRIPTION: PASSENGER VEHICLES. A DECKLID WIRE HARNESS CAN FATIGUE AND DEVELOP BROKEN WIRES IN THE BEND AREA OF THE WIRE HARNESS.

Manufacturer’s stated response

DEALERS WILL REPLACE THE DECKLID WIRE HARNESS.

Manufacturer campaign: 00S50

Reported concern

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE REAR WHEEL HUB RETAINING NUTS CAN LOOSEN AND ALLOW THE LEFT REAR WHEEL AND BRAKE DRUM ASSEMBLY TO SEPARATE FROM THE VEHICLE.

Manufacturer’s stated response

DEALERS WILL INSPECT THE REAR WHEEL BEARINGS AND INSTALL A REAR WHEEL RETENTION CAP TO PREVENT LEFT REAR WHEEL SEPARATION. OWNER NOTIFICATION BEGAN OCTOBER 12, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.

Manufacturer campaign: 00S31

Reported concern

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH SPEED CONTROL AND AUTOMATIC TRANSMISSION. A SPEED CONTROL CABLE COULD HAVE A CORE WIRE THAT IS LONG ENOUGH TO CATCH ON THE SLEEVE AT THE THROTTLE BODY END OF THE CABLE DURING WIDE-OPEN THROTTLE ACCELERATION.

Manufacturer’s stated response

DEALERS WILL INSPECT THESE VEHICLES AND, IF NECESSARY, REPLACE THE SPEED CONTROL CABLE. OWNER NOTIFICATION BEGAN OCTOBER 12, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.

Manufacturer campaign: 00S30

Reported concern

VEHICLE DESCRIPTION: PASSENGER VEHICLES. CERTAIN VEHICLES FAIL TO COMPLY WITH REQUIREMENTS OF FMVSS NO. 201, "OCCUPANT PROTECTION IN INTERIOR IMPACT." THE RESULTANT HIC(D) VALUE AT ONE TARGET LOCATION AP1, LOCATED ON THE TRIM PANEL AT THE JUNCTURE OF THE A-PILLAR AND ROOF SIDE RAIL, MAY BE GREATER THAN DESIGN INTENT.

Manufacturer’s stated response

DEALERS WILL REMOVE THE LEFT AND RIGHT SIDE B-PILLAR AND A-PILLAR TRIM PANELS, REVISE THE HEADLINER EDGE NEAR THE TOPS OF THE A-PILLARS TO ACCEPT THE NEW A-PILLAR TRIM PANELS WITH THEIR ENERGY ABSORBING TUBES, AND INSTALL THE NEW A-PILLAR AND THE OLD B-PILLAR TRIM PANELS.

Manufacturer campaign: 00S20

Reported concern

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH SPEED CONTROL. THE SPEED CONTROL CABLE END FITTING CAN ALLOW WATER TO ENTER THE SPEED CONTROL SERVO ASSEMBLY. IF THIS OCCURS, CORROSION IN THE SERVO ASSEMBLY COULD DEVELOP AND CAUSE INTERMITTENT SPEED CONTROL OPERATION OR PREVENT THE THROTTLE FROM RETURNING TO IDLE.

Manufacturer’s stated response

DEALERS WILL REPLACE THE SPEED CONTROL CABLE (WITH A NEW CABLE THAT INCORPORATES A GLASS-FILLED END CAP) AND INSPECT THE ASSEMBLY FOR INTERNAL CORROSION. SERVOS WITH EVIDENCE OF CORROSION WILL ALSO BE REPLACED. OWNERS ARE ADVISED NOT TO USE THE SPEED CONTROL UNTIL THE VEHICLES ARE REPAIRED.