The vehicle dossier US · 2006
2006 Ford
F-150Problems & recalls
585 distinct owner reports in the NHTSA snapshot. Engine appears in 151 of them. Explore what was reported—and which official actions are on file.
01 / Owner-reported evidence
What owners reported.
Categories attached to 585 distinct reports. A report can mention more than one component, so category totals can overlap.
See original component labels
These are reports made to NHTSA, not verified diagnoses. More reports can reflect more vehicles, more time on the road, or greater reporting activity.
The reporting timeline
When reports arrived.
Reports by year filed, not by the year a problem occurred. Showing the latest 15 years with reports.
61,000 miles is the median among 501 reports with usable mileage. The middle half spans 28,000–98,000 miles.
This describes the submitted reports. It does not predict when a vehicle will fail.
02 / Official safety campaigns
14 recall campaigns on file.
A campaign can cover only certain production dates or configurations. The count does not tell you whether an individual car has an open recall.
AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULECampaign 11V107000
Reported concern
FORD IS RECALLING CERTAIN MODEL YEAR 2004-2006 F-150 PICK UP TRUCKS AS WELL AS CERTAIN MODEL YEAR 2006 LINCOLN MARK LT VEHICLES. IF THE CLOCKSPRING JUMPER WIRE COMES IN CONTACT WITH THE DRIVER SIDE FRONTAL AIR BAG LOWER HORN PLATE, THE WIRE INSULATION MAY BECOME CHAFED, CREATING A POTENTIAL FOR A SHORT CIRCUIT. IF THIS OCCURS THE AIR BAG WARNING LAMP MAY ILLUMINATE INDICATING THAT SERVICE IS REQUIRED.
Manufacturer’s stated response
FORD WILL NOTIFY OWNERS AND INSTRUCT THEM TO TAKE THEIR VEHICLES TO A FORD OR LINCOLN/MERCURY DEALER TO HAVE A NEW CLOCKSPRING JUMPER WIRE INSTALLED THAT INCORPORATES A PROTECTIVE MESH COVER. REPAIRS WILL BE PERFORMED FREE OF CHARGE. THIS SAFETY RECALL BEGAN ON SOME VEHICLES IN MARCH 2011. THE RECALL CAMPAIGN ON THE EXPANDED POPULATION IS EXPECTED TO BEGIN ON OR ABOUT MAY 9, 2011. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Manufacturer campaign: 11S18
Read campaign 11V107000 at NHTSAEXTERIOR LIGHTING:HEADLIGHTSCampaign 09E025000
Reported concern
DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.
Manufacturer’s stated response
DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.
Read campaign 09E025000 at NHTSAEXTERIOR LIGHTINGCampaign 09E012000
Reported concern
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.
Manufacturer’s stated response
SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.
Read campaign 09E012000 at NHTSASERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM:HOSES, LINES/PIPING, AND FITTINGSCampaign 08V208000
Reported concern
FORD IS RECALLING 605,684 MY 2005-2006 F-150 AND LINCOLN MARK LT VEHICLES EQUIPPED WITH 5.4L 3-VALVE ENGINES. THE BRAKE BOOSTER VACUUM SUPPLY HOSE ATTACHED TO THE INTAKE MANIFOLD FITTING MAY SWELL OVER TIME AND LOSE RETENTION FORCE. THIS CONDITION COULD ALLOW THE HOSE TO BECOME DETACHED FROM THE FITTING DURING AN INTAKE MANIFOLD BACKFIRE. SHOULD THE HOSE DETACH FROM THE INTAKE MANIFOLD, SEVERAL BRAKE APPLICATIONS WITH POWER ASSIST WILL BE AVAILABLE BEFORE THE VACUUM RESERVE IS DEPLETED.
Manufacturer’s stated response
DEALERS WILL REPLACE A RUBBER HOSE ON THE BRAKE BOOSTER VACUUM SUPPLY TUBE ASSEMBLY. THE RECALL BEGAN ON JUNE 27, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Manufacturer campaign: 08S05
Read campaign 08V208000 at NHTSAEXTERIOR LIGHTING:HEADLIGHTSCampaign 07E089000
Reported concern
CERTAIN SPYDER HEADLAMP REPLACEMENT ASSEMBLIES SOLD FOR USE ON 2004 THROUGH 2007 FORD F150 PICKUP TRUCKS. DURING PRODUCTION, THE HEADLAMPS WERE INTERNALLY MISALIGNED AND THEY FAIL THE PHOTOMETRY REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
Manufacturer’s stated response
SPYDER WILL NOTIFY OWNERS AND OFFER A FULL REIMBURSEMENT FOR ANY NONCOMPLIANT HEADLAMPS. THE RECALL IS EXPECTED TO BEGIN DURING NOVEMBER 2007. OWNERS CAN CONTACT SPYDER AT 866-558-4264.
Read campaign 07E089000 at NHTSAEXTERIOR LIGHTING:HEADLIGHTSCampaign 07E080000
Reported concern
CERTAIN HEADLAMP ASSEMBLIES IMPORTED AND SOLD AS AFTERMARKET EQUIPMENT BY SONAR AUTO PARTS FOR USE ON 2004-2007 FORD F150 PICKUP TRUCKS. DURING PRODUCTION, THE HEADLAMPS WERE INTERNALLY MISALIGNED AND THEY FAIL THE PHOTOMETRY REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
Manufacturer’s stated response
SONAR WILL NOTIFY OWNERS AND OFFER A FULL REIMBURSEMENT FOR ANY NONCOMPLIANT HEADLAMPS. THE RECALL BEGAN ON DECEMBER 14, 2007. OWNERS CAN CONTACT SONAR AT 866-558-4264.
Read campaign 07E080000 at NHTSAEXTERIOR LIGHTING:HEADLIGHTSCampaign 07E075000
Reported concern
CERTAIN EAGLE EYES HEADLAMP ASSEMBLIES, P/NOS. FR390-B001L AND FR390-B001R, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THE THICKNESS IS UNSTABLE INHIBITING THE PERFORMANCE OF THE UPPER AND LOWER BEAMS WHICH FAILS TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
Manufacturer’s stated response
EAGLE EYES WILL NOTIFY OWNERS AND OFFER REIMBURSEMENT FOR ANY NONCOMPLIANT HEADLIGHTS. THE RECALL BEGAN ON NOVEMBER 6, 2007. OWNERS MAY CONTACT EAGLE EYES AT 1-800-568-1098.
Read campaign 07E075000 at NHTSAEQUIPMENT:ELECTRICALCampaign 07E066000
Reported concern
CERTAIN CEQUENT 90 DEGREE 7-WAY RIGHT ANGLE ADAPTORS SOLD BY DISTRIBUTORS IN TOW PACKAGES FOR AFTERMARKET SALES TO TOW 5TH WHEEL RV TRAVEL TRAILERS. DUE TO INCORRECT WIRING OF THE HARNESS, THE TRAILER LIGHTS MAY NOT OPERATE PROPERLY.
Manufacturer’s stated response
ALL OF THE DEFECTIVE TOW PACKAGES ARE STILL AT THE DISTRIBUTOR LEVEL AND HAVE NOT BEEN SOLD TO ANY CONSUMERS.
Read campaign 07E066000 at NHTSAEXTERIOR LIGHTINGCampaign 06E064000
Reported concern
CERTAIN TRADESONIC COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
Manufacturer’s stated response
TRADESONIC WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JULY 2006. OWNERS MAY CONTACT TRADESONIC AT 626-934-8884.
Read campaign 06E064000 at NHTSAEXTERIOR LIGHTINGCampaign 06E060000
Reported concern
CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."
Manufacturer’s stated response
AAI MOTORSPORTS WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 1, 2006. OWNERS MAY CONTACT AAI MOTORSPORTS AT 909-923-9188.
Read campaign 06E060000 at NHTSAEXTERIOR LIGHTING:HEADLIGHTSCampaign 06E023000
Reported concern
CERTAIN ANZO COMBINATION HEADLAMP ASSEMBLIES SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES. SOME COMBINATION LAMPS ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS WHICH FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."
Manufacturer’s stated response
ANZO WILL NOTIFY OWNERS AND REPLACE THE HEADLAMPS FREE OF CHARGE. THE RECALL BEGAN MAY 9, 2006. OWNERS MAY CONTACT ANZO USA AT 909-468-3688.
Read campaign 06E023000 at NHTSAINTERIOR LIGHTINGCampaign 06V033000
Reported concern
CERTAIN PICKUP TRUCKS FAIL TO COMPLY WITH EITHER THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 105, 'HYDRAULIC AND ELECTRIC BRAKE SYSTEMS' OR FMVSS NO. 135, 'PASSENGER CAR BRAKE SYSTEMS.' THESE VEHICLES WERE BUILT WITH A SOFTWARE ERROR IN THE INSTRUMENT CLUSTER.
Manufacturer’s stated response
DEALERS WILL RECALIBRATE THE INSTRUMENT CLUSTER IN THESE VEHICLES. THE RECALL BEGAN ON FEBRUARY 27, 2006. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Manufacturer campaign: 06C11
Read campaign 06V033000 at NHTSATIRES:TREAD/BELTCampaign 05T022000
Reported concern
CERTAIN CONTINENTAL CONTITRAC TR OWL, CONTITRAC TR BSW, GENERAL GRABBER TR BSW, AND CONTITRAC BSW TIRES MANUFACTURED BETWEEN MAY 29 AND JUNE 11, 2005, AND SOLD AS ORIGINAL EQUIPMENT ON CERTAIN FORD TRUCKS AND SOLD AS REPLACEMENT TIRES. THESE TIRES CAN WEAR PREMATURELY WHICH FAILS TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 119, NEW PNEUMATIC TIRES FOR VEHICLES OTHER THAN PASSENGER CARS.
Manufacturer’s stated response
CONTINENTAL WILL NOTIFY OWNERS AND REPLACE THE TIRES FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 7, 2005. OWNERS MAY CONTACT CONTINENTAL AT 704-588-5895.
Read campaign 05T022000 at NHTSAVISIBILITY:WINDSHIELD WIPER/WASHER:MOTORCampaign 05V520000
Reported concern
ON CERTAIN TRUCKS, PASSENGER CARS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE BEING APPLIED TO THE OUTPUT SHAFT GEAR.
Manufacturer’s stated response
DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 22, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673 OR LINCOLN/MERCURY AT 1-800-521-4140.
Manufacturer campaign: 05S40
Read campaign 05V520000 at NHTSA03 / The manufacturer’s record
Instructions. Updates. Responses.
56 distinct communications list this model-year. Showing the latest 12. A matching model-year does not establish that every engine, trim or reported symptom is covered.
TSB 24-2188This article supersedes TSB 22-2219 to update the Parts List and Service Procedure to clarify applicable steps by vehicle application. Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with …NHTSA ID 11005305
This article supersedes TSB 22-2219 to update the Parts List and Service Procedure to clarify applicable steps by vehicle application. Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
Components: WHEELS. Confirm detailed applicability in the original document.
Source record 11005305 at NHTSASSM 51536For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identif…NHTSA ID 10235153
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
Components: STRUCTURE. Confirm detailed applicability in the original document.
Source record 10235153 at NHTSATSB 22-2219Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated w…NHTSA ID 10214754
Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
Components: POWER TRAIN. Confirm detailed applicability in the original document.
Source record 10214754 at NHTSATSB 20-2307Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 vehicles equipped with TOD transfer cases may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated…NHTSA ID 10181917
Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 vehicles equipped with TOD transfer cases may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure steps to remove and cap the vacuum supply line.
Components: ELECTRICAL SYSTEM · EQUIPMENT · WHEELS. Confirm detailed applicability in the original document.
Source record 10181917 at NHTSATSB 20-2233This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or pee…NHTSA ID 10177863
This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
Components: STRUCTURE. Confirm detailed applicability in the original document.
Source record 10177863 at NHTSADOR-N3Z7B-03This SKU is an Oil Dipstick. The customer communication requested return of unsold inventory to inspect the dipstick tube. The dipstick tube inner diameter may be small enough that it prevents installation of the OE dipstick.NHTSA ID 10172885
This SKU is an Oil Dipstick. The customer communication requested return of unsold inventory to inspect the dipstick tube. The dipstick tube inner diameter may be small enough that it prevents installation of the OE dipstick.
Components: ENGINE AND ENGINE COOLING. Confirm detailed applicability in the original document.
Source record 10172885 at NHTSASSM 48157Some 2002-2008 F-Super Duty, F-150 and Mark LT vehicles may exhibit concern during or after programing the VSM. The programming may fail or vehicle symptoms such as inoperative door locks, dome lamps, door ajar indicators or au…NHTSA ID 10165713
Some 2002-2008 F-Super Duty, F-150 and Mark LT vehicles may exhibit concern during or after programing the VSM. The programming may fail or vehicle symptoms such as inoperative door locks, dome lamps, door ajar indicators or auto lamps may occur after successful programing. To ensure the VSM is configured correctly, use the Integrated Diagnostic System (IDS) scan tool and select the blue ball and socket icon in the upper left corner. Select the utility knife in the bottom left corner. Select Update/Special Function and enter 53061 in the blue box then press the tick mark. The screen will go back to the system utilities page. Navigate to the toolbox tab and run the Programmable Module Installation (PMI) on the VSM. The procedure will prompt you to manually enter the as-built into the VSM. Obtain the as-built data from PTS > OASIS > As-Built.
Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.
Source record 10165713 at NHTSADORD2Q5Z09This SKU is a Transmission Oil Cooler Line. The customer communication requested return of unsold inventory to inspect for the port size being too large. If the port size is too large it will not fit the mating component which …NHTSA ID 10165335
This SKU is a Transmission Oil Cooler Line. The customer communication requested return of unsold inventory to inspect for the port size being too large. If the port size is too large it will not fit the mating component which would prevent installation, and would therefore have no impact on the end user besides time to complete installation.
Components: POWER TRAIN. Confirm detailed applicability in the original document.
Source record 10165335 at NHTSATSB 19-2026Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is re…NHTSA ID 10156863
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
Components: EQUIPMENT · STRUCTURE. Confirm detailed applicability in the original document.
Source record 10156863 at NHTSATSB 19-2026Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is re…NHTSA ID 10155551
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
Components: STRUCTURE. Confirm detailed applicability in the original document.
Source record 10155551 at NHTSASSM 47331Various vehicles equipped with a 4.6L, 5.4L, 6.8L modular 3 valve engine built on or before 8-Jan-2016 may exhibit symptoms that may include upper end engine noise, rough running, misfire and/or engine damage. If diagnosis lead…NHTSA ID 10143079
Various vehicles equipped with a 4.6L, 5.4L, 6.8L modular 3 valve engine built on or before 8-Jan-2016 may exhibit symptoms that may include upper end engine noise, rough running, misfire and/or engine damage. If diagnosis leads to only camshaft/camshaft roller follower(s) requiring replacement, replace all of the camshaft roller followers on both banks/cylinder heads with part number 3L3Z-6564-A, not just the faulty roller follower(s). When replacing the camshaft roller followers, refer to Workshop Manual (WSM), Section 303-01.
Components: ENGINE · EQUIPMENT. Confirm detailed applicability in the original document.
Source record 10143079 at NHTSASSM 46542When ordering a 2005 to 2008 remanufactured 5.4L 3v or 6.8L 3v engine, spark plug boots may be provided in the packaging. Replace all black spark plug boots from the original engine with the 'brown' spark plug boots, as provide…NHTSA ID 10109021
When ordering a 2005 to 2008 remanufactured 5.4L 3v or 6.8L 3v engine, spark plug boots may be provided in the packaging. Replace all black spark plug boots from the original engine with the 'brown' spark plug boots, as provided. The updated 'brown' spark plug boots are longer than the black boots to accommodate a running change in the spark plug length. The ignition coil bodies and spring/resistor are transferable and only the rubber boots require replacement. Failure to install the spark plug boots provided with the replacement engine could lead to drivability concerns.
Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.
Source record 10109021 at NHTSARecords below contain the NHTSA bulk summary unless a document-reviewed explainer is linked. A service bulletin is not a safety recall or a promise of a free repair. Records may be revised or superseded; verify the current document with the manufacturer.
04 / Agency investigations
Official inquiries.
An investigation is an inquiry into a potential concern. Its presence does not establish a defect, and a closed case does not certify a car’s condition.
Inadvertent airbag deploymentEA10001
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Recorded closure: Apr 25, 2011
Campaign reference in the source: 11V107000
Find investigation EA10001LOSS OF BRAKE POWER-ASSISTPE08001
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Recorded closure: May 9, 2008
Campaign reference in the source: 08V208000
Find investigation PE08001Your next step
Take good questions
to the inspection.
Use these prompts with a qualified inspector. This page is research, not a diagnosis or a substitute for a hands-on inspection.