2006 BMW
530IProblems & recalls

The basic conditions for initializing the power windows are not met.

Components: ELECTRICAL SYSTEM · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Confirm detailed applicability in the original document.

The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle “discharged battery” complaints.

Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.

Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE

Components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE. Confirm detailed applicability in the original document.

Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicle’s equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.

Components: ELECTRICAL SYSTEM · EQUIPMENT. Confirm detailed applicability in the original document.

Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Note: Opening, closing and starting via the BMW Digital Key or the Digital Key Card are not affected.

Components: ELECTRICAL SYSTEM · EQUIPMENT. Confirm detailed applicability in the original document.

Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.

Components: SERVICE BRAKES, AIR:DISC · STEERING: STEERING WHEEL/HANDLE BAR. Confirm detailed applicability in the original document.

Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.

Components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY. Confirm detailed applicability in the original document.

Power Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.

Components: ENGINE AND ENGINE COOLING. Confirm detailed applicability in the original document.

Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.

Components: ELECTRICAL SYSTEM · POWER TRAIN. Confirm detailed applicability in the original document.

Various Electrical Problems Caused by Water Ingress. Water ingress into the luggage compartment may cause various electrical problems or faults associated with the MPM (Micro Power Module); PDC (Park Distance Control); M-ASK (Multi-Audio System Controller); CCC (Car Communication Computer); CID (Control Information Display); TCU (Telematics Control Unit); LOGIC-7 (Top Hi-Fi); RDC (Tire Pressure Monitor) or SDARS (Satellite Radio Receiver) control modules. In most cases, the water collects in the spare wheel recess. CAUSE: Insufficient sealing may allow water to enter the luggage compartment due to the vacuum generated while driving.

Components: ELECTRICAL SYSTEM · STRUCTURE. Confirm detailed applicability in the original document.

"Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME. The ""Service Engine Soon"" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled, the engine then usually performs normally. The following faults are stored in the DME: * 2A82 VANOS intake - stiff; jammed mechanically * 2A87 VANOS exhaust - stiff; jammed mechanically * 130108 VANOS intake: control fault, position not reached * 130308 VANOS exhaust: control fault, position not reached For the N54 engine, the following secondary faults may also be stored: * 120408 Charge-air pressure control, cut-out: Boost pressure accumulation blocked * 3100 Boost-pressure control, deactivation - boost-pressure buildup prohibited CAUSE The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. If engine operation requires the VANOS system to quickly advance or retard the intake or exhaust camshaft, faults may be stored if the camshaft is ""late"", or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 or 120408 can also be set in the DME fault memory as well."

Components: ENGINE · EQUIPMENT. Confirm detailed applicability in the original document.

NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:

Components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Confirm detailed applicability in the original document.